Hi,
I am new to shell scripting and have a question. I would like to redirect the output of a command to multiple files, each file holding the exact same copy. From what I read from the bash manpage and from some searching it seems it cannot be done within the shell except setting up a loop. Is... (3 Replies)
Hello,
I have a java program which i am calling in shell script. I wanted to redirect output to 2 differetn files. Output should have both 1 & 2 (normal and error) in both file.
pls help (2 Replies)
Hi
There are many posts in this forum regarding reditecting output, but mine is a different problem, please have a look.
My shell script is redirecting output to a log file dynamically. That is it is using -
exec > log1.txt 2>&1
Hence all the traces are appearing in the log1.txt.
I want... (3 Replies)
Hi
i am compiling a source code by make command.
i want to redirect the output of make to a file but at the same time i want to see the output in terminal.
how to do this ?.
please suggest your idea.
thanks in advance.
Saravana
---------- Post updated at 05:24 PM ----------... (2 Replies)
How to redirect the output to multiple files without putting on console
I tried tee but it writes to STDOUT , which I do not want.
Test.sh
------------------
#!/bin/ksh
echo "Hello " tee -a file1 file2
----------------------------
$>./Test.sh
$>
Expected output:
-------------------... (2 Replies)
hi,
i want to redirect my output & error if generated to two different files. I
have written the code for redirecting the output, i dnt have ne idea how to
go abt it for errors. I tried spooling which was given in one of the
threads on this forum.But it didn't work.The script i wrote as a lot... (4 Replies)
Below script perfectly works, giving below mail output. BUT, I want to make the script mail only if there are any D-Defined/T-Transition/B-Broken State WPARs and also to copy the output generated during monitoring to a temporary log file, which gets cleaned up every week. Need suggestions.
... (4 Replies)
Hi Guys,
I want to redirect the output of 3 scripts to a file and then mail the output of those three scripts.
I used below but it is not working:
OFILE=/home/home1/report1
echo "report1 details" > $OFILE
=/home/home1/1.sh > $OFILE
echo... (7 Replies)
Hi,
when I do cat for kernel parameters
cat /proc/sys/kernel/sem >> /etc/sysctl.conf
4096 4096 32 128
The above command working with out any doubt
but I want to pass it like below, need to append "kernel.sem =" and pass it to /etc/sysctl.conf kernel.sem = 4096... (2 Replies)
Discussion started by: stew
2 Replies
LEARN ABOUT OSF1
tee
tee(1) General Commands Manual tee(1)NAME
tee - Displays the output of a program and copies it into a file
SYNOPSIS
tee [-ai] file...
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
tee: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
OPTIONS
Adds the output to the end of file instead of writing over it. Ignores the SIGINT signal.
OPERANDS
Standard input is stored into, or appended to, the file specified.
[Tru64 UNIX] The tee command can accept up to 20 file arguments.
DESCRIPTION
The tee command reads standard input and writes to both standard output, and each specified file.
The tee command is useful when you wish to view program output as it is displayed, and also want to save it in a file. The tee command does
not buffer output, so you may wish to pipe the output of tee to more if more than one full screen of data is anticipated.
NOTES
If a write to any file fails, the exit status of tee will be non-zero. Writes to all other specified files may be successful, and opera-
tion will continue until standard input is exhausted.
EXIT STATUS
The following exit values are returned: Successful completion. An error occurred.
EXAMPLES
To view and save the output from a command at the same time, enter: lint program.c | tee program.lint
This displays the standard output of the command lint program.c at the terminal, and at the same time saves a copy of it in the file
program.lint. If program.lint already exists, it is deleted and replaced. To display and append to a file, enter: lint program.c |
tee -a program.lint
This displays the standard output of lint program.c at the terminal and at the same time appends a copy of it to the end of pro-
gram.lint. If the file program.lint does not exist, it is created.
ENVIRONMENT VARIABLES
The following environment variables affect the execution of tee: Provides a default value for the internationalization variables that are
unset or null. If LANG is unset or null, the corresponding value from the default locale is used. If any of the internationalization vari-
ables contain an invalid setting, the utility behaves as if none of the variables had been defined. If set to a non-empty string value,
overrides the values of all the other internationalization variables. Determines the locale for the interpretation of sequences of bytes
of text data as characters (for example, single-byte as opposed to multibyte characters in arguments). Determines the locale for the for-
mat and contents of diagnostic messages written to standard error. Determines the location of message catalogues for the processing of
LC_MESSAGES.
SEE ALSO
Commands: cat(1), echo(1), script(1)
Standards: standards(5)tee(1)