03-11-2020
I was able to figure it out and able to configure. Thanks for the help
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
7. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
8. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
9. Solaris
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT SUSE
genlib_unflatten_lofig
GENLIB_UNFLATTEN_LOFIG.3(October 1, 1997) GENLIB_UNFLATTEN_LOFIG.3(October 1, 1997)
NAME
UNFLATTEN_LOFIG - creates a hierarchy level from instances in the current logical figure
SYNOPSYS
#include <genlib.h>
void GENLIB_UNFLATTEN_LOFIG(figurename, instancename, list_of_instances, 0)
char *figurename;
char *instancename;
char *list_of_instances;
ORIGIN
This software belongs to the ALLIANCE CAD SYSTEM developed by the ASIM team at LIP6 laboratory of Universite Pierre et Marie CURIE, in
Paris, France.
Web : http://asim.lip6.fr/recherche/alliance/
E-mail : alliance-users@asim.lip6.fr
PARAMETERS
figurename Name of the figure of the new hierarchy to be created
instancename Name to be given at the instanciation of figurename into the current structual figure
list_of_instances List of strings representing the instances to be inserted into the new figure
DESCRIPTION
UNFLATTEN_LOFIG creates a new level of hierarchy, whose model name will be figurename, and instanciate it under the name instancename in
the current figure. The instances whose name belong to the list_of_instances parameters are added in the new figure, and destroyed from
the current figure.
EXAMPLE
#include <genlib.h>
main()
{
/* Create a figure to work on */
GENLIB_DEF_LOFIG("mycell");
.
.
.
/* Place an instance */
GENLIB_LOINS("model","instance", "sig1", "sig2", EOL);
/* flatten an instance */
GENLIB_UNFLATTEN_LOFIG("newfig", "newins", "instance", ..., 0);
/* Save all that on disk */
GENLIB_SAVE_LOFIG();
}
SEE ALSO
genlib(1), GENLIB_FLATTEN_LOFIG(3).
BUG REPORT
This tool is under development at the ASIM department of the LIP6 laboratory.
We need your feedback to improve documentation and tools.
PROCEDURAL GENERATION LANGUAGE
ASIM/LIP6 GENLIB_UNFLATTEN_LOFIG.3(October 1, 1997)