03-05-2020
On aggr0 you can only define IP address from native VLAN on those ports.
If you wish to define a tagged IP on the hypervisor, you need to create vlan interface, then define IP on that.
If you wish to use the interface for virtual machines, you define a VSW with aggr0 link.
Then you add a vnet via ldm command using that VSW.
You can have both on the hypervisor, vlan interfaces and VSW above aggr0, but of course with different IP addresses (vm and hypervisor).
I would recommend reading about Oracle VM server for SPARC and a bit about networking as well
Looks like you are mixing hypervisor and vm part regarding network.
Regards
Peasant.
These 2 Users Gave Thanks to Peasant For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
7. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
8. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
9. Solaris
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies