Sponsored Content
Operating Systems Solaris Solaris 11 link aggregation with multiple VLANs - not working Post 303044832 by solaris_1977 on Wednesday 4th of March 2020 11:04:23 PM
Old 03-05-2020
Thanks for the suggestion.

I am expecting this setup, as the whole picture. Hope it makes sense.

One single interface (be it aggr or ipmp) with one IP will be presented to OVM (OV Manager) as host, as an IP with multiple VLAN tagged. After finishing the repository and other post-work, I should be create VM.
For example, I can get a request "create a Solaris-10 VM with 2 interfaces, one VLAN#2170 and one VLAN#2161". This interface will be visible on OVM Manager as bond0.

We have more than 20 VLANs, so don't want to configure 20 IPs for each VLAN. Ideally, all those VLANs should be tagged on this single interface. Any suggestion, how can I achieve it?
Please ask, if I am not able to explain it well.
 

9 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

4. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

6. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

7. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

8. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

9. Solaris

Solaris link aggregation not working as expected

Hi, This is Solaris-10 x86 platform. I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise. # netstat -nr Routing Table: IPv4 Destination Gateway Flags Ref Use Interface --------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
VLAN(4) 						   BSD Kernel Interfaces Manual 						   VLAN(4)

NAME
vlan -- IEEE 802.1Q VLAN network interface SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device vlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_vlan_load="YES" DESCRIPTION
The vlan driver demultiplexes frames tagged according to the IEEE 802.1Q standard into logical vlan network interfaces, which allows rout- ing/bridging between multiple VLANs through a single switch trunk port. Each vlan interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). To function, a vlan interface must be assigned a parent interface and numeric VLAN tag using ifconfig(8). A single parent can be assigned to multiple vlan interfaces provided they have different tags. The parent interface is likely to be an Ethernet card connected to a properly configured switch port. The VLAN tag should match one of those set up in the switched network. Initially vlan assumes the same minimum length for tagged and untagged frames. This mode is selected by the sysctl(8) variable net.link.vlan.soft_pad set to 0 (default). However, there are network devices that fail to adjust frame length, should it fall below the allowed minimum due to untagging. Such devices should be able to interoperate with vlan after changing the value of net.link.vlan.soft_pad to 1. In the latter mode, vlan will pad short frames before tagging them so that their length stays not less than the minimum value after untagging by the non-compliant devices. HARDWARE
The vlan driver supports efficient operation over parent interfaces that can provide help in processing VLANs. Such interfaces are automati- cally recognized by their capabilities. Depending on the level of sophistication found in a physical interface, it may do full VLAN process- ing or just be able to receive and transmit long frames (up to 1522 bytes including an Ethernet header and FCS). The capabilities may be user-controlled by the respective parameters to ifconfig(8), vlanhwtag and vlanmtu. However, a physical interface is not obliged to react to them: It may have either capability enabled permanently without a way to turn it off. The whole issue is very specific to a particular device and its driver. By now, the list of physical interfaces able of full VLAN processing in the hardware is limited to the following devices: ae(4), age(4), alc(4), ale(4), bce(4), bge(4), cxgb(4), em(4), ixgb(4), jme(4), msk(4), nge(4), re(4), sge(4), stge(4), ti(4), txp(4), and vge(4). The rest of the Ethernet interfaces can run VLANs using software emulation in the vlan driver. However, some of them lack the capability of transmitting and receiving long frames. Assigning such an interface as the parent to vlan will result in a reduced MTU on the corresponding vlan interfaces. In the modern Internet, this is likely to cause tcp(4) connectivity problems due to massive, inadequate icmp(4) filtering that breaks the Path MTU Discovery mechanism. The following interfaces support long frames for vlan natively: bfe(4), cas(4), dc(4), fwe(4), fxp(4), gem(4), hme(4), le(4), nfe(4), nve(4), rl(4), sf(4), sis(4), sk(4), ste(4), tl(4), tx(4), vr(4), and xl(4). The vlan driver automatically recognizes devices that natively support long frames for vlan use and calculates the appropriate frame MTU based on the capabilities of the parent interface. Some other interfaces not listed above may handle long frames, but they do not advertise this ability of theirs. The MTU setting on vlan can be corrected manually if used in conjunction with such a parent interface. SEE ALSO
ifconfig(8), sysctl(8) BUGS
No 802.1Q features except VLAN tagging are implemented. BSD
April 14, 2010 BSD
All times are GMT -4. The time now is 04:20 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy