|
|
Sponsored Content
Special Forums
Hardware
Arduino Robot Tank Project
Post 303043244 by Neo on Wednesday 22nd of January 2020 06:10:02 AM
|
|
6 More Discussions You Might Find Interesting
1. Windows & DOS: Issues & Discussions
Hi All
Im running veritas netbackup 6.5.5, on MWindows 2003 master server.
Ive just added a Quantum PX500 with 2 drives, the problem im facing is that now under the storage unit tab on console all the storage unit types for NDMP have the new robot listed and not the original one. The set up i... (0 Replies)
Discussion started by: blossy786
0 Replies
2. Programming
In my further exploration of Arduino, today I decided to install the arduino-cli on my mac today.
https://github.com/arduino/arduino-cli
I followed the instructions for macOS but when I got to this part:
arduino-cli board list
I got the dreaded "Unknown" Fully Qualified Board Name... (1 Reply)
Discussion started by: Neo
1 Replies
3. Programming
HI all...
(Apologies for any typos.)
To add to Neo's Arduino subject matter I have decided to upload this in ".zip" format.
Ignore "*.info" files these are AMIGA icons only and also the "HAM" drawer as these are photos in ancient AMIGA HAM modes.
I have noticed that there are current... (6 Replies)
Discussion started by: wisecracker
6 Replies
4. Programming
Just finished a quick Python script to send the current unix time over to the Arduino from macOS, so in the absence of GPS or some other way to get the unix timestamp (epoch time) to the Arduino, I can get my macOS and Arduino UNO synced to within a second.
Normally, when the Arduino starts... (9 Replies)
Discussion started by: Neo
9 Replies
5. Programming
My favorite projects are always related to the "latest" tech in command and control, networking and network communications. This Elecrow GSM/GPRS/EDGE SIM5360E 3G Shield seems to be the "latest and the greatest" as far as 3G and GPS, as far as I can see so far, but I has it drawbacks for sure.... (6 Replies)
Discussion started by: Neo
6 Replies
6. Programming
This post describes a "work in progress" project I started today. Here is the High Level Overview:
Currently, this project sits on my desk as an Arduino UNO (on the bottom), an NB-IoT Shield (sandwiched in the middle), a Sensor Shield (on top) with a HM-10 BLE Module (in the little... (13 Replies)
Discussion started by: Neo
13 Replies
LEARN ABOUT SUSE
hd
HD(4) Linux Programmer's Manual HD(4) NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)