Well, when XPIC is enabled and Autorestore in NOT Enabled (in the example is Unknown but could be something else like "Disabled"), I have to take the related slot number to create a specified command (to execute it later).
So in the above example, slot 2:
- XPIC is enabled and Autorestore is Uknown
- Create outut command like: rl 2 xpicrecovery 5 5 (where 2 is the slot number)
Same for slot 3
- XPIC is enabled and Autorestore is Uknown
- Create outut command like: rl 3 xpicrecovery 5 5 (where 3 is the slot number)
Slot 4:
XPIC is disable (no autorestore variable present)
Just skip.....
Hello,
I am wondering if you can assist with my question and ask kindly for this.
I have a number of files that are listed as file1.gz through file100.gz.
I am trying to perform a grep on the files and find a specific date that only resides within within one of the files. There are... (3 Replies)
am using txr command (txr 1097) on a process that generates the following output. Im trying to extract the 13th field from the highlighted string. it is delimited by '?'. The 13th field corresponds to the '0' (in bold). can you let me know how I can extract the 13 th field please?
... (1 Reply)
am using txr command (txr 1097) on a process that generates the following output. Im trying to extract the 13th field from the highlighted string. it is delimited by '?'. The 13th field corresponds to the '0' (in bold). can you let me know how I can extract the 13 th field please?
... (1 Reply)
Hi Everyone,
New to the forum, and have my first question.
I have the following Macro currently being used within Telnet to run a report for the date being entered. However, now I need the Macro to input the day after today to the the day after today.
Example: If today is May 9, 2012 - the... (0 Replies)
Hello,
I would need some help, :wall: on a linux script,
I am not sure how can I separate some text file,
Text file contains something similar to this:
share "userhome_e" "/fs1_100g/FILE58/userhome" umask=022 maxusr=4294967295 netbios=FILE58
share "bu share"... (3 Replies)
I need to grab information from the output of the ps command.
For each line of ps output that contains _progres -b I need to get the word that follows -p. The "-p" can be anywhere after "_progres -b".
Using grep to select the correct lines is no problem (e.g. ps -ef|grep "_progres \-b|grep -v... (3 Replies)
My scenario is as follows.
1. I have a reference file with the IP addresses and names
$ cat ref.list
10.11.xxx.xxx AA
10.12.xxx.xxx BB
10.13.xxx.xxx CC
10.14.xxx.xxx DD
2. A script runs and gets me one of the IP addresses and puts it in a separate file, for e.g... (2 Replies)
hi, i have a file A like this:
******************* No 2823 ********************
contig15205-
G383C4U02H4G80+ is in contig15205-
G383C4U02HGLXM- is in contig15205-
G383C4U01C3HIZ+ is in contig15205-
... (3 Replies)
Hi,
I am trying to extract a specific information from a file which contains more than 200 million records. Attached the input file for your reference.
My file contains information below
... (4 Replies)
Gents,
Using the following code i am able to output the information i need, but some of the strings are not complete due to the separator : used..
Kindly can u help me to get all string after the first :
Example in the output file column 16 i should get
17/11/25 03:43:51:732000
but i... (8 Replies)
Discussion started by: jiam912
8 Replies
LEARN ABOUT REDHAT
amtape
AMTAPE(8) System Manager's Manual AMTAPE(8)NAME
amtape - user interface to Amanda tape changer controls
SYNOPSIS
amtape config command [ command options ]
DESCRIPTION
Amtape performs tape changer control operations. It uses the underlying tape changer script defined by the tpchanger option for a particu-
lar Amanda configuration as specified by the config argument.
Tape changers maintain a notion of the current and next slot for each configuration. These may or may not correspond to an actual physical
state of the device, but do tend to minimize searching through the tape storage slots. If the desired tape is in the current slot, it is
likely the next tape needed is in the next slot rather than at some random position in the storage slots.
See the amanda(8) man page for more details about Amanda.
COMMANDS
reset Reset the tape changer to a known state. The current slot is set to the first slot. Other device-specific side effects may occur.
Some gravity stackers need to be reset to the top position by hand. This command notifies Amanda the stacker is back in that posi-
tion.
eject If a tape is loaded in the drive, it is ejected and returned to the slot from which it was loaded.
clean If a cleaning tape is defined for the changer, it is used to clean the drive.
show Show the contents of all slots. This can be slow.
label label
Search for and load the Amanda tape with label label.
taper Perform the taper scan algorithm. Load the next tape in the configuration's tape sequence, or a fresh tape with a suitable label.
device Display the name of the current tape device on stdout.
current
Display the current slot.
update Update the changer label database, if it has one, to match the tapes now available.
slot slot
Eject any tape in the drive and put it away, then load the tape from slot slot and reset current.
slot current
Eject any tape in the drive and put it away, then load the tape from the current slot.
slot prev
Eject any tape in the drive and put it away, then load the tape from the previous slot and reset current.
slot next
Eject any tape in the drive and put it away, then load the tape from the next slot and reset current.
slot first
Eject any tape in the drive and put it away, then load the tape from the first slot and reset current.
slot last
Eject any tape in the drive and put it away, then load the tape from the last slot and reset current.
slot advance
Eject any tape in the drive and put it away. Advance current to the next tape, but do not load it.
This is useful with non-gravity stackers to unload the last tape used and set up Amanda for the next run. If you just use eject,
the current tape will be mounted again in the next run, where it will be rejected as being still in use, ejected and the next tape
requested. Using slot next followed by eject does an unnecessary mount.
Note: most changers optimize the slot commands to not eject the loaded tape if it is the one being requested.
AUTHOR
James da Silva <jds@cs.umd.edu>
University of Maryland, College Park
SEE ALSO amanda(8)AMTAPE(8)
01-18-2020
