Strange combination, sparc linux on Solaris ldom, to notice at first.
I do not think that is supported or condoned by Oracle, but since you installed / booted it lets take a look.
Can you show output of :
What linux distribution is this ?
Hi,
Need help for the network configuration on Solaris 10 5/8.
My NIC's dirver was loaded after Solaris installation and is configured using static ip address for a local network: 172.16.1.12
I have configured set of files as: /etc/hosts :
172.16.1.12 ls12
/etc/hostname.iprb0:... (7 Replies)
Howdy
I am using Fedora12 with KVM, with XP64pro as a guest. Everything seems to be working just fine, BUT I can't Save. When I do instruction KVM to save, I get a continuing Saving display, but it continues for a long time until I finally terminate it due to boredom :) I have let it run for... (0 Replies)
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it.... (4 Replies)
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine
The network goes through VLAN 503 (level, network tagget)
And I need to give network to the guest domain: madarrwebsol10
I hope someone can bring some light ....
Excuse my English ...
... (4 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies
LEARN ABOUT CENTOS
grub2-file
GRUB-FILE(1) General Commands Manual GRUB-FILE(1)NAME
grub-file -- Check if FILE is of specified type.
SYNOPSIS
grub-file (--is-i386-xen-pae-domu | --is-x86_64-xen-domu |
--is-x86-xen-dom0 | --is-x86-multiboot |
--is-x86-multiboot2 | --is-arm-linux | --is-arm64-linux |
--is-ia64-linux | --is-mips-linux | --is-mipsel-linux |
--is-sparc64-linux | --is-powerpc-linux | --is-x86-linux |
--is-x86-linux32 | --is-x86-kfreebsd | --is-i386-kfreebsd |
--is-x86_64-kfreebsd | --is-x86-knetbsd |
--is-i386-knetbsd | --is-x86_64-knetbsd | --is-i386-efi |
--is-x86_64-efi | --is-ia64-efi | --is-arm64-efi |
--is-arm-efi | --is-hibernated-hiberfil | --is-x86_64-xnu |
--is-i386-xnu | --is-xnu-hibr | --is-x86-bios-bootsector)
FILE
DESCRIPTION
grub-file is used to check if FILE is of a specified type.
OPTIONS --is-i386-xen-pae-domu
Check if FILE can be booted as i386 PAE Xen unprivileged guest kernel
--is-x86_64-xen-domu
Check if FILE can be booted as x86_64 Xen unprivileged guest kernel
--is-x86-xen-dom0
Check if FILE can be used as Xen x86 privileged guest kernel
--is-x86-multiboot
Check if FILE can be used as x86 multiboot kernel
--is-x86-multiboot2
Check if FILE can be used as x86 multiboot2 kernel
--is-arm-linux
Check if FILE is ARM Linux
--is-arm64-linux
Check if FILE is ARM64 Linux
--is-ia64-linux
Check if FILE is IA64 Linux
--is-mips-linux
Check if FILE is MIPS Linux
--is-mipsel-linux
Check if FILE is MIPSEL Linux
--is-sparc64-linux
Check if FILE is SPARC64 Linux
--is-powerpc-linux
Check if FILE is POWERPC Linux
--is-x86-linux
Check if FILE is x86 Linux
--is-x86-linux32
Check if FILE is x86 Linux supporting 32-bit protocol
--is-x86-kfreebsd
Check if FILE is x86 kFreeBSD
--is-i386-kfreebsd
Check if FILE is i386 kFreeBSD
--is-x86_64-kfreebsd
Check if FILE is x86_64 kFreeBSD
--is-x86-knetbsd
Check if FILE is x86 kNetBSD
--is-i386-knetbsd
Check if FILE is i386 kNetBSD
--is-x86_64-knetbsd
Check if FILE is x86_64 kNetBSD
--is-i386-efi
Check if FILE is i386 EFI file
--is-x86_64-efi
Check if FILE is x86_64 EFI file
--is-ia64-efi
Check if FILE is IA64 EFI file
--is-arm64-efi
Check if FILE is ARM64 EFI file
--is-arm-efi
Check if FILE is ARM EFI file
--is-hibernated-hiberfil
Check if FILE is hiberfil.sys in hibernated state
--is-x86_64-xnu
Check if FILE is x86_64 XNU (Mac OS X kernel)
--is-i386-xnu
Check if FILE is i386 XNU (Mac OS X kernel)
--is-xnu-hibr
Check if FILE is XNU (Mac OS X kernel) hibernated image
--is-x86-bios-bootsector
Check if FILE is BIOS bootsector
SEE ALSO
info grub
Web Feb 26 2014 GRUB-FILE(1)