Operating Systems SCO SCO OS 6 Driver for LSIL SAS1064E Raid Controller Post 303039604 by hicksd8 on Thursday 10th of October 2019 05:51:09 AM
Phew! It's been a long time since I did this but AFAIR it goes like this for a configuration like you are trying to achieve (boot from add-in disk in order to see data on an old controller).

Quote:
I managed to download the OpenServer 6.0 enterprise server installation media and the MPT driver and install it.
So you have installed the RAID controller driver???? How did you do that?? What command did you use?

From memory, I think it must be either.......

Code:
# custom

or

Code:
# scoadmin

or

Code:
# mkdev hd         <- This one might work in any case.

Now, to build such a configuration you would install SCO O/S on the new disk (which you have done) and then insert the RAID controller (okay it's already in there). You would then need to:
1. Run one of the above commands to add the RAID controller driver to the kernel.
2. Relink the kernel, say 'Y' to rebuild the boot environment, and reboot.
3. Run the same command AGAIN to add the disk(s) attached to the RAID controller into the kernel configuration. This will ask for stuff like bus# and unit# (like you would for a SCSI controller - unit# being SCSI ID, etc).
4. Relink the kernel AGAIN, say 'Y' to rebuild the boot environment AGAIN, and reboot AGAIN.
5. Now the device node (/dev/<whatever> should be there and the mount command is no different to any other disk.

6. If you configure the disk(s) wrongly you can run the command yet again to unconfigure, relink, and reboot. Then do it correctly.

I hope that helps. Perhaps you have installed the RAID driver, stopped there and not configured any disk(s)??????

As I said, this is all from memory. Another member, expert at SCO (jgt) might chip in and confirm whether I'm right or wrong.

Good luck. I'm sure you'll get there.

Last edited by hicksd8; 10-10-2019 at 08:06 AM..
 
Test Your Knowledge in Computers #720
Difficulty: Medium
Alan Minsky was an adviser on Stanley Kubrick's movie 2001: A Space Odyssey.
True or False?

10 More Discussions You Might Find Interesting

1. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon (1 Reply)
Discussion started by: karzon
1 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

RAID controller needed for SVM?

hi this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network) i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies

4. Hardware

Problem with External Raid Controller.

Hi, We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks. This also has an External Raid Controller (Storagetek Eight-Port, External HBA Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk. ... (1 Reply)
Discussion started by: ranjansukumar
1 Replies

5. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

6. AIX

Internal PCI X RAID Controller issue ?

Hello folks, Could someone tell me why I unable to create pdisks for a RAID Array # lscfg | grep scsi + sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter + scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies

7. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

8. SCO

How to change raid controller driver ? (hardware change)

Hello I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller . The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver) What ... (3 Replies)
Discussion started by: flako
3 Replies

9. Red Hat

Separate HDD test using RAID controller

Hello, I am using Red Hat 2.6.23.1 with RAID 6 controller (card). (When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.) I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies

10. SCO

SCO 5.0.7 driver for HP SmartArray P410i Controller on Proliant DL380 G7?

Hi I hope this is the right forum. I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller. I need a driver for this. Can anybody point me to a download? Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
uhci(7D)							      Devices								  uhci(7D)

NAME
uhci - host controller driver SYNOPSIS
pcivid,pid@unit-address DESCRIPTION
The uhci host controller driver is a USBA (Solaris USB Architecture) compliant nexus driver that supports the Universal Host Controller Interface Specification 1.1, an industry standard developed by Intel. The uhci driver supports all USB transfers, including interrupt, con- trol, isochronous and bulk. FILES
/kernel/drv/uhci 32-bit ELF kernel module. (SPARC or x86). /kernel/drv/amd64/uhci 64-bit ELF kernel module. (x86). /kernel/drv/sparcv9/uhci 64-bit SPARC ELF kernel module. /kernel/drv/uhci.conf Driver configuration file. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+---------------------------------+ |ATTRIBUTE TYPE |ATTRIBUTE VALUE | +-----------------------------+---------------------------------+ |Architecture |SPARC or x86 PCI-based systems | +-----------------------------+---------------------------------+ |Availability |SUNWusb | +-----------------------------+---------------------------------+ SEE ALSO
attributes(5), ehci(7D), hubd(7D), ohci(7D), usba(7D) Writing Device Drivers Universal Host Controller Interface Specification for USB 1.1 Universal Serial Bus Specification 2.0 System Administration Guide: Basic Administration http://www.sun.com/io DIAGNOSTICS
All host controller errors are passed to the client drivers. Root errors are documented in hubd(7D). In addition to being logged, the following messages may appear on the system console. All messages are formatted in the following manner: WARNING: <device path> <uhci><instance number>>: Error message... No SOF interrupts have been received. This USB UHCI host controller is unusable. The USB hardware is not generating Start Of Frame interrupts. Please reboot the system. If this problem persists, contact your system vendor. SunOS 5.11 26 July 2005 uhci(7D)
All times are GMT -4. The time now is 05:23 AM.
Unix & Linux Forums Content Copyright 1993-2020. All Rights Reserved.
Privacy Policy