I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
hi, i was trying to mirror root volume group and the command i was using didnt respond for a long time
mirrorvg -m rootvg hdisk1
I was checking rootvg and it gives below. how do i fix stale partitions?? it seems to be on hdisk1
LV NAME TYPE LPs PPs PVs LV STATE ... (2 Replies)
HP-UX B.11.23 U ia64
I've got two users that show in "w" with long idle times but if I search for their processes I find nothing (ps -ef | grep username )
I'm not sure why "w" still sees them and if there is anything (short of a reboot) that I can do to clean them out.
Ideas? (8 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hellow friends,
We are having AIX 5.3 total memory allotted to /Backup directory is 700GB actual used memory is 250GB ..but when i issue df -gt command to check space it is showing /Backup directory is 70% full ..how to identify root cause.? (1 Reply)
Hello,
I have an ancient HP-UX 11.11 system where I have a logical volume marked stale and I can't get it sync'd. I have tried lvsync and lvreduce/lvextend to no avail. It is just one 4Mb PE on the disk that I can't get current.
# lvdisplay -v /dev/vg00/lvol5 | grep stale
LV Status ... (17 Replies)
Hi friends,
the paging lv hd6 is in stale condition
hd6 paging 48 96 2 open/stale N/A
And i'am getting the following alerts in the server 333BD283 0811044814 U S LVDD Bad block detected with no relocation al
333BD283 0811041114 U S LVDD ... (1 Reply)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
I have a AIX 7.1 system that has 3 failed disks, 1 in rootvg and 2 in vg_usr1.
Here is the output of lspv.
# lspv
hdisk0 00044d4dfbb11575 vg_usr1 active
hdisk1 0000150179158027 vg_usr1 active
hdisk2 ... (11 Replies)
Discussion started by: c3rb3rus
11 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)