Sponsored Content
Operating Systems SCO SCO OS 6 Driver for LSIL SAS1064E Raid Controller Post 303037166 by hicksd8 on Thursday 25th of July 2019 07:50:24 AM
Old 07-25-2019
I think where you need to go is here:

ftp://ftp.sco.com/pub/openserver6/600/drivers

I also think you need to follow "MPT_810" for the LSI 1064e RAID controller.

Give that a go.

Last edited by hicksd8; 07-25-2019 at 08:57 AM..
This User Gave Thanks to hicksd8 For This Post:
 

10 More Discussions You Might Find Interesting

1. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon (1 Reply)
Discussion started by: karzon
1 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

RAID controller needed for SVM?

hi this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network) i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies

4. Hardware

Problem with External Raid Controller.

Hi, We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks. This also has an External Raid Controller (Storagetek Eight-Port, External HBA Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk. ... (1 Reply)
Discussion started by: ranjansukumar
1 Replies

5. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

6. AIX

Internal PCI X RAID Controller issue ?

Hello folks, Could someone tell me why I unable to create pdisks for a RAID Array # lscfg | grep scsi + sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter + scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies

7. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

8. SCO

How to change raid controller driver ? (hardware change)

Hello I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller . The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver) What ... (3 Replies)
Discussion started by: flako
3 Replies

9. Red Hat

Separate HDD test using RAID controller

Hello, I am using Red Hat 2.6.23.1 with RAID 6 controller (card). (When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.) I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies

10. SCO

SCO 5.0.7 driver for HP SmartArray P410i Controller on Proliant DL380 G7?

Hi I hope this is the right forum. I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller. I need a driver for this. Can anybody point me to a download? Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
COMPAT_IBCS2(8) 					    BSD System Manager's Manual 					   COMPAT_IBCS2(8)

NAME
compat_ibcs2 -- setup procedure for running iBCS2 binaries DESCRIPTION
NetBSD supports running Intel Binary Compatibility Standard 2 (iBCS2) binaries. This only applies to i386 systems for now. Binaries are supported from SCO UNIX and other systems derived from AT&T System V Release 3 UNIX. iBCS2 support is only well tested using SCO binaries. XENIX binaries are also supported although not as well tested. SVR4 binaries are supported by the COMPAT_SVR4 option. iBCS2 supports COFF, ELF, and x.out (XENIX) binary formats. Binaries from SCO OpenServer (version 5.x) are the only ELF binaries that have been tested. Most programs should work, but not ones that use or depend on: kernel internal data structures STREAMS drivers (other than TCP/IP sockets) local X displays (uses a STREAMS pipe) virtual 8086 mode The iBCS2 compatibility feature is active for kernels compiled with the COMPAT_IBCS2 option enabled. If support for iBCS2 ELF executables is desired, the EXEC_ELF32 option should be enabled in addition to COMPAT_IBCS2. Many COFF-format programs and most ELF-format programs are dynamically linked. This means that you will also need the shared libraries that the program depends on. Also, you will need to create a ``shadow root'' directory for iBCS2 binaries on your NetBSD system. This directory is named /emul/ibcs2. Any file operations done by iBCS2 programs run under NetBSD will look in this directory first. So, if an iBCS2 pro- gram opens, for example, /etc/passwd, NetBSD will first try to open /emul/ibcs2/etc/passwd, and if that does not exist open the 'real' /etc/passwd file. It is recommended that you install iBCS2 packages that include configuration files, etc. under /emul/ibcs2, to avoid nam- ing conflicts with possible NetBSD counterparts. Shared libraries should also be installed in the shadow tree. Generally, you will need to look for the shared libraries that iBCS2 binaries depend on only the first few times that you install an iBCS2 program on your NetBSD system. After a while, you will have a sufficient set of iBCS2 shared libraries on your system to be able to run newly imported iBCS2 binaries without any extra work. Setting up shared libraries How to get to know which shared libraries iBCS2 binaries need, and where to get them? Depending on the file type of the executable, there are different possibilities (when following these instructions: you will need to be root on your NetBSD system to do the necessary installation steps). COFF binaries You can simply copy all of the available shared libraries since they are fairly small in size. The COFF shared libraries are typically found in /shlib and can be obtained from the following sources: SCO UNIX version 3.x (aka ODT) SCO UNIX version 5.x (aka OpenServer) SCO UnixWare Many versions of SVR4.2/x86 After copying the shared libraries, you should have at least the following files on your system: /emul/ibcs2/shlib/libc_s /emul/ibcs2/shlib/libnsl_s /emul/ibcs2/shlib/protlib_s ELF binaries You can simply copy all of the available shared libraries from the source system or distribution or use ldd(1) to determine the libraries required by a specific binary. After copying the shared libraries, you should have at least the following files on your system: /emul/ibcs2/usr/lib/libc.so.1 /emul/ibcs2/usr/lib/libcrypt.so /emul/ibcs2/usr/lib/libndbm.so /emul/ibcs2/usr/lib/libsocket.so.1 If you don't have access to a SCO system, you will need to get the extra files you need from a SCO distribution. As of January 1998, SCO sells a copy of SCO OpenServer (iBCS2) and/or SCO UnixWare (SVR4) for personal/non-commercial use for only the cost of shipping (about $20US). The distribution comes on an ISO9660-format CDROM which can be mounted and used to copy the necessary files. Run the following script to copy the basic set of files from a SCO distribution directory mounted somewhere locally: /usr/share/examples/emul/ibcs2/ibcs2-setup [directory] You should now be set up for SCO binaries which only need standard shared libs. BUGS
The information about SCO distributions may become outdated. Attempting to a use a nameserver on the local host does not currently work due to an absurd shortcut taken by the iBCS2 network code (remem- ber that there are no kernel sockets). 16/32/64 bit offsets may not be handled correctly in all cases. BSD
February 8, 1998 BSD

Featured Tech Videos

All times are GMT -4. The time now is 09:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy