03-26-2019
Quote:
Originally Posted by
filosophizer
how can one solve "mismatch between the LPAR type and the booting image"
hmm, just to make sure i understand the situation correctly:
- you have (POWER6) managed system
- you want to boot from an internal disk
- on the disk a VIOS image is installed
On the case of 3 "yes"es: you need to install the LPAR anyway, so boot it via NIM methods (mksysb+spot). You can the select the disk to install to and this disk will be wiped first, so the VIOS image will go away. Only then (after installation) you can boot from the disk.
I hope this helps.
bakunin
10 More Discussions You Might Find Interesting
1. AIX
When using PowerVM Express and IVM (no HMC) on a Power6 P520 , can I configure 2 LPARs in addition to a VIO server, or does the VIO Server count as one of the two LPAR's that PowerVM Express allows? (1 Reply)
Discussion started by: JodyTek
1 Replies
2. AIX
Hi everyone,
Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Discussion started by: need2bageek
2 Replies
3. AIX
hi guys,
i need to develop following setup for a customer:
high availability oracle database on aix7 and linux in 2 different LPAR using dual ps700 blande a ds3400 and HMC.
the question is, it is possible to have automatic vioc failover(aix,linux) when for example 1 vios goes down?
in... (6 Replies)
Discussion started by: gullio23
6 Replies
4. AIX
Hi all please give me a link for IBM PowerVM (4 Replies)
Discussion started by: babinlonston
4 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
Discussion started by: filosophizer
2 Replies
7. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
8. AIX
I am facing problems in moving CD-ROM from one lpar to another.
CDROM can be seen on the POWERVM (IVM) server , but through the web-access if I move it ( assign it ) to LPAR it will be assigned. I run cfgmgr , and the cdrom does not show up in the LPAR. I firmly believe this is the reason why I... (2 Replies)
Discussion started by: filosophizer
2 Replies
9. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
10. AIX
coming from this thread: https://www.unix.com/aix/211107-ibm-power-pseries-open-firmware-boot-vios-powervm-vet-code.html
PowerVM, formerly known as Advanced Power Virtualization (APV), is a chargeable feature of IBM POWER5, POWER6, POWER7, POWER8, and POWER9 servers and is required for support... (0 Replies)
Discussion started by: filosophizer
0 Replies