03-11-2019
There are several issues you will have to deal with.
The first: do you have the root password? you will not be able to start the machine in single user mode without it.
Second: this machine has an IDE hard drive which will be difficult to replace.
Third: what is the actual release of SCO? The release number should be 5.0.? where ? is probably 5 through 7.
This manual may help
http://tim.id.au/laptops/lenovo/thinkpad%20t30.pdf
This User Gave Thanks to jgt For This Post:
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
5. Ubuntu
Hi guys, I am total newbie to Linux / Ubuntu but trying it to solve the problem I have.
I have an OKI printer with bad HDD and trying to clone one from the same HDD from working printer. Board it goes on has a Fiery chipset and system used is Linux based / related - to the best of my knowlege. I... (12 Replies)
Discussion started by: Unlimitedbt
12 Replies
6. HP-UX
Hi there,
I got a pretty old HP 382 workstation, and the hdd is pretty LOUD ... ;)
So I thought I clone it to an much quiter one.
I tried this:
- removed the loud hdd
- connected it to an system running knoppix 7.0.4 (hdd is recognized with UFS filesystem; Clonezilla couldn't handle the... (9 Replies)
Discussion started by: pelegrine
9 Replies
7. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
8. AIX
Hi Folks,
I am facing an issue with the performance.
P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes
P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
LEARN ABOUT PHP
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)