Today (Saturday) We will make some minor tuning adjustments to MySQL.

You may experience 2 up to 10 seconds "glitch time" when we restart MySQL. We expect to make these adjustments around 1AM Eastern Daylight Saving Time (EDT) US.

"Need Hardware help on a RP4440 that lost the RTC and does not see both hard drives"

Post #303029741 by vbe on Thursday 31st of January 2019 01:18:51 PM

Related Linux and UNIX Technical Support
Hard drives
Will some one tell me what this means. "warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20." I'm running SCO 505 on a proliant 1600r. Thnank you in advance.... UNIX for Dummies Questions & Answers
UNIX for Dummies Questions & Answers
No Hard Drives Have Been Found
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives...... Linux
Is my data lost? Installed Linux, no longer can I access my hard drives.
Here's the story - I installed Linux on my Y drive, and all went well until I tried to boot into XP again. I can't access or install an operating system to my other three hard drives, C, X, and Z. I think that during the install my hard drives were changed to something other then NTFS, but...... Linux
Help adding new hard drives
Folks; I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version. Is there a command i can use to add the new space or even see if the system can sees them?... Filesystems, Disks and Memory
Filesystems, Disks and Memory
Reinstall old hard drives
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot...... Solaris
HD(4)							     Linux Programmer's Manual							     HD(4)

hd - MFM/IDE hard disk devices
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd*
chown(1), mknod(1), sd(4), mount(8)
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at Linux 1992-12-17 HD(4)

Featured Tech Videos