Anyone know of a guide or instructions for Solaris
I got to configure a SBUS HBA to talk to a tape robot.
I have done this on a switch but not point to point.
just going HBA >>>>> TAPE Fibre simple two nodes
Kie (6 Replies)
Hi!
I'm new in these forums and more or less new with Unix. So... here is the question:
does anyone know where is redirected the output of a command when you put >&- after it?
Does it means any standard file descriptor?
Thanks! (2 Replies)
hi,
I would like to ask or is it possible to dump a hex using dd from starting point to end point just like the "xxd -s 512 -l 512 <bin file>"
I know the redirect hexdump -C but i can't figure it out the combination options of dd.
Hope someone can share their knowledge..
Thanks in... (3 Replies)
Discussion started by: jao_madn
3 Replies
4. Post Here to Contact Site Administrators and Moderators
HI Everyone,
I have below source file
AAA|NAME1|ADDRESS1|300.20
BBB|NAME2|ADDRESS2|400.31
CCC|NAME3|ADDRESS3|300.34
I have requirement where I need to sum up fourth field in above fixed width pipe delimited flat file. When I use below code, it gives me value 1001.00
But I am expecting... (1 Reply)
Hey all! :)
I'm trying to create a fixed mount point for an usb cardreader.
I've found a script on a raspberry pi forum which does the following:
usb stick is plugged in -> script checks the mount point for data -> script starts copying the files automatically -> script unmounts the... (0 Replies)
How to create a new mount point with 600GB and add 350 GBexisting mount point
Best if there step that i can follow or execute before i mount or add diskspace IN AIX
Thanks (2 Replies)
Well, guys I saw a question about GOTO for Python.
So this gave me the inspiration to attempt a GOTO function for 'dash', (bash and ksh too).
Machine: MBP OSX 10.14.3, default bash terminal, calling '#!/usr/local/bin/dash'...
This is purely a fun project to see if it is possible in PURE... (3 Replies)
Discussion started by: wisecracker
3 Replies
LEARN ABOUT CENTOS
sas_disk_blink
SAS_DISK_BLINK(8) SDPARM SAS_DISK_BLINK(8)NAME
sas_disk_blink - blink the LED on a SAS disk
SYNOPSIS
sas_disk_blink [--help] [--set NUM] [--verbose] DEVICE
DESCRIPTION
This bash shell script attempts to blink the LED on the SAS disk referred to by DEVICE. By default the LED will blink for 30 seconds. This
is meant to help identify which disk corresponds to a given DEVICE.
The script use the sdparm utility and manipulates the "Ready LED Meaning" (RLM) field in the Protocol specific port mode page in order to
blink the LED.
OPTIONS
Arguments to long options are mandatory for short options as well.
-h, --help
print out the usage message then exit.
-s, --set NUM
when NUM is 0 then the RLM field is cleared. When NUM is 1 then the RLM field is set. When NUM > 1 then the SAS disk LED is made to
blink for NUM seconds. If this option is not given then the SAS disk LED is made to blink for 30 seconds.
-v, --verbose
increase level or verbosity.
EXIT STATUS
The exit status of this script is 0 when it is successful. Otherwise the exit status is that of the last sdparm utility called. See the
sdparm(8) man page.
AUTHORS
Written by D. Gilbert
COPYRIGHT
Copyright (C) 2013 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
SEE ALSO
sdparm (sdparm)
sdparm-1.08 May 2013 SAS_DISK_BLINK(8)