05-16-2018
Solution found: the bridge is created,but doesn't work.
Instead of bridge wlan and eth I create a network virtual wich point to wlan0 with virt-manager.
Works fine
8 More Discussions You Might Find Interesting
1. AIX
We are using hp's network node manager and would like to monitor quite a few of our aix boxes. It appears that nnm does not have AIX mibs by default. Does anyone know where i can find mibs for aix to load into nnm? Thanks (0 Replies)
Discussion started by: zuessh
0 Replies
2. Windows & DOS: Issues & Discussions
Okay. I need help since I barely use M$ any more, the last time I used it for something other than school, work, or AIM was back in the days of WIN98. I was just reading the article on this site, Is Microsoft about to release a Windows “kill switch”? | Ed Bott's Microsoft Report | ZDNet.com, and... (0 Replies)
Discussion started by: Texasone
0 Replies
3. Shell Programming and Scripting
Hello all :)
I am new to scripting. I need somebody to help me write a script that can edit the files.
For eg: if i say ./script <ipadd> <hostname>
then it should change the ipaddress and hostname in the following files:
1. /etc/hosts
2. /etc/sysconfig/network
3.... (1 Reply)
Discussion started by: Shaikjaveed
1 Replies
4. Red Hat
hi,
i would like to share this
/etc/sysconfig/network-script/route-eth0
GATEWAY0=XXXXXX
NETMASK0=XXXXXX
ADDRESS0=XXXXXXX
a delete route command with "route del -net xxxx...." will work but if the above exist and you reboot the linux then old route will be invoke on that config-route.
... (0 Replies)
Discussion started by: itik
0 Replies
5. UNIX for Dummies Questions & Answers
Hellow,
I have a smc2582w-b brigde/acces point whom i configured on my windows vista pc and it works i have wireless acces to my network.
Then i plugged it in to my 420r enterprise and it doesn't give any link activity on the lan piece of my server and my bridge/AP
when i plug the cable... (3 Replies)
Discussion started by: chelle007
3 Replies
6. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
7. Linux
Dear Engineer,
Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it.
With Best Regards,
Md. Abdullah-Al Kauser (0 Replies)
Discussion started by: makauser
0 Replies
8. Red Hat
Dear Engineer,
Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it.
With Best Regards,
Md. Abdullah-Al Kauser (1 Reply)
Discussion started by: makauser
1 Replies
LEARN ABOUT DEBIAN
parprouted
PARPROUTED(8) Proxy ARP Bridging Daemon PARPROUTED(8)
NAME
parprouted - Proxy ARP IP bridging daemon
SYNOPSIS
parprouted [-d] [-p] interface [interface]
DESCRIPTION
parprouted is a daemon for transparent IP (Layer 3) proxy ARP bridging. Unlike standard bridging, proxy ARP bridging allows to bridge Eth-
ernet networks behind wireless nodes. Normal L2 bridging does not work between wireless nodes because wireless does not know about MAC
addresses used in the wired Ethernet networks. Also this daemon is useful for making transparent firewalls.
The daemon listens for incoming ARP requests, and in case the location of the requested IP address is unknown, forwards them to other
interfaces, as well as updates kernel ARP table with the received replies. When necessary, the daemon generates an ARP reply itself, which
causes the stations to send traffic to the host daemon is running on. By automatically adding appropriate /32 routes to Linux kernel IP
routing table for the hosts learned via ARP, daemon ensures that the Linux kernel will be able to route the packets to the destination host
when it receives them without any need routing/subnetting manually.
All routes entered by the daemon have a metric of 50.
Unless you use -p switch, all entries in the ARP table will be refreshed (rechecked by sending ARP requests) every 50 seconds. This keeps
them from being expired by kernel.
Normally it takes about 60 ms for a bridge to update all its tables and start sending packets to the destination.
REQUIREMENTS
This daemon can be used for unicast traffic only. I.e., DHCP is not supported. Use software such as dhcrelay to "bridge" DHCP.
You should have an IP address assigned on all of your interfaces that you do bridging on. There is no need for this address to be from the
same networks as the bridged networks. Any dummy address will do.
The system should have correct default route.
parprouted requires "ip" program from iproute2 tools to be installed in /sbin. If it is installed in another location, please replace
"/sbin/ip" occurances in the source with the correct path. As well you should have proc filesystem mounted in /proc because the daemon uses
/proc/net/arp.
parprouted is designed for and tested only with Linux 2.4.x kernels.
OPTIONS
The list of interfaces to do bridging on should be given via the command line.
The daemon accepts the following switches:
-d, which stands for debugging. If you run it in debugging mode the daemon will not go to background and will print additional debugging
information to stdout/stderr.
-p, which makes all ARP entries to be permanent. This will also result in that ARP tables will not be refreshed by ARP pings.
EXAMPLE
To bridge between wlan0 and eth0: parprouted eth0 wlan0
AUTHOR
(C) 2004, Vladimir Ivaschenko <vi@maks.net>
http://www.hazard.maks.net
parprouted January 2004 PARPROUTED(8)