05-14-2018
Installation on SCO Openserver 5.0.5
Hello all,
First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help!
Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5 as its O/S. This software hasn't been used in 2 years as we changed to a different company. I would like to put this software back on the previous server, that way I can re-commission this new server for in house data backups. I have already re-installed the software on the old from the backup tapes (they run nightly) but I am getting a few errors.
1- sh-fork failed - too many processes
2- login.sco error - failed to initialize policy manager daemon
Not sure if they are linked or not? Any help would be greatly appreciated! Thanks
Last edited by crt001; 05-14-2018 at 05:48 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
lsmsad(8) System Manager's Manual lsmsad(8)
NAME
lsmsad - Starts the Storage Administrator (SA) daemon
SYNOPSIS
/usr/sbin/lsmsad
DESCRIPTION
The SA daemon, lsmsad, is a process required by lsmsa, the SA graphical user interface (GUI). The daemon issues commands and obtains system
information on behalf of SA.
The SA daemon runs on a Tru64 UNIX system on which LSM is initialized and running. The SA client runs on any machine that supports the
Java Runtime Environment.
The SA daemon is automatically started at boot time. Under normal conditions, the daemon does not need to be run manually.
If SA does not start during the boot process, enter:
/sbin/init.d/lsmsa stop
To restart SA, enter:
/sbin/init.d/lsmsa start
Only one SA daemon can be running on a system at a given time. If a second SA daemon attempts to start, it will fail.
RESTRICTIONS
You must be root user to run lsmsad.
FILES
The script that starts lsmsad at boot time. The command log file that tracks SA tasks. The access log file that tracks login to SA. The
server log file that tracks server startup information and server errors. The log maintenance shell script that saves and compresses log
files.
SEE ALSO
lsmsa(8), volintro(8)
lsmsad(8)