Sponsored Content
Operating Systems Linux Is possible to bridge wlan0 and eth0 using network manager?How to for wpa? Post 303015902 by Linusolaradm1 on Monday 16th of April 2018 07:06:50 AM
Old 04-16-2018
Is possible to bridge wlan0 and eth0 using network manager?How to for wpa?

I have created a bridge with nmcli between eth0 and wlan0

I use this procedure

Code:
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0 bridge.stp no
sudo nmcli con down eth0
sudo nmcli con down wlan0
sudo nmcli up br0

The bridge works,i can ping is ipv4 address..but..how to do for wpa2?
I prefer to use nmcli.
 

8 More Discussions You Might Find Interesting

1. AIX

AIX and HP Network Node Manager

We are using hp's network node manager and would like to monitor quite a few of our aix boxes. It appears that nnm does not have AIX mibs by default. Does anyone know where i can find mibs for aix to load into nnm? Thanks (0 Replies)
Discussion started by: zuessh
0 Replies

2. Windows & DOS: Issues & Discussions

WPA crash vista???

Okay. I need help since I barely use M$ any more, the last time I used it for something other than school, work, or AIM was back in the days of WIN98. I was just reading the article on this site, Is Microsoft about to release a Windows “kill switch”? | Ed Bott's Microsoft Report | ZDNet.com, and... (0 Replies)
Discussion started by: Texasone
0 Replies

3. Shell Programming and Scripting

Need help: Script to edit the hosts, network and eth0 file

Hello all :) I am new to scripting. I need somebody to help me write a script that can edit the files. For eg: if i say ./script <ipadd> <hostname> then it should change the ipaddress and hostname in the following files: 1. /etc/hosts 2. /etc/sysconfig/network 3.... (1 Reply)
Discussion started by: Shaikjaveed
1 Replies

4. Red Hat

[tip] network route-eth0

hi, i would like to share this /etc/sysconfig/network-script/route-eth0 GATEWAY0=XXXXXX NETMASK0=XXXXXX ADDRESS0=XXXXXXX a delete route command with "route del -net xxxx...." will work but if the above exist and you reboot the linux then old route will be invoke on that config-route. ... (0 Replies)
Discussion started by: itik
0 Replies

5. UNIX for Dummies Questions & Answers

smc2582w-b bridge and solaris 10 wireless network

Hellow, I have a smc2582w-b brigde/acces point whom i configured on my windows vista pc and it works i have wireless acces to my network. Then i plugged it in to my 420r enterprise and it doesn't give any link activity on the lan piece of my server and my bridge/AP when i plug the cable... (3 Replies)
Discussion started by: chelle007
3 Replies

6. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ... (0 Replies)
Discussion started by: Tanmoy
0 Replies

7. Linux

Network bandwidth Manager

Dear Engineer, Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it. With Best Regards, Md. Abdullah-Al Kauser (0 Replies)
Discussion started by: makauser
0 Replies

8. Red Hat

Network bandwidth Manager

Dear Engineer, Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it. With Best Regards, Md. Abdullah-Al Kauser (1 Reply)
Discussion started by: makauser
1 Replies
sudo_root(8)						      System Manager's Manual						      sudo_root(8)

NAME
sudo_root - How to run administrative commands SYNOPSIS
sudo command sudo -i INTRODUCTION
By default, the password for the user "root" (the system administrator) is locked. This means you cannot login as root or use su. Instead, the installer will set up sudo to allow the user that is created during install to run all administrative commands. This means that in the terminal you can use sudo for commands that require root privileges. All programs in the menu will use a graphical sudo to prompt for a password. When sudo asks for a password, it needs your password, this means that a root password is not needed. To run a command which requires root privileges in a terminal, simply prepend sudo in front of it. To get an interactive root shell, use sudo -i. ALLOWING OTHER USERS TO RUN SUDO
By default, only the user who installed the system is permitted to run sudo. To add more administrators, i. e. users who can run sudo, you have to add these users to the group 'admin' by doing one of the following steps: * In a shell, do sudo adduser username admin * Use the graphical "Users & Groups" program in the "System settings" menu to add the new user to the admin group. BENEFITS OF USING SUDO
The benefits of leaving root disabled by default include the following: * Users do not have to remember an extra password, which they are likely to forget. * The installer is able to ask fewer questions. * It avoids the "I can do anything" interactive login by default - you will be prompted for a password before major changes can happen, which should make you think about the consequences of what you are doing. * Sudo adds a log entry of the command(s) run (in /var/log/auth.log). * Every attacker trying to brute-force their way into your box will know it has an account named root and will try that first. What they do not know is what the usernames of your other users are. * Allows easy transfer for admin rights, in a short term or long term period, by adding and removing users from the admin group, while not compromising the root account. * sudo can be set up with a much more fine-grained security policy. * On systems with more than one administrator using sudo avoids sharing a password amongst them. DOWNSIDES OF USING SUDO
Although for desktops the benefits of using sudo are great, there are possible issues which need to be noted: * Redirecting the output of commands run with sudo can be confusing at first. For instance consider sudo ls > /root/somefile will not work since it is the shell that tries to write to that file. You can use ls | sudo tee /root/somefile to get the behaviour you want. * In a lot of office environments the ONLY local user on a system is root. All other users are imported using NSS techniques such as nss-ldap. To setup a workstation, or fix it, in the case of a network failure where nss-ldap is broken, root is required. This tends to leave the system unusable. An extra local user, or an enabled root password is needed here. GOING BACK TO A TRADITIONAL ROOT ACCOUNT
This is not recommended! To enable the root account (i.e. set a password) use: sudo passwd root Afterwards, edit the sudo configuration with sudo visudo and comment out the line %admin ALL=(ALL) ALL to disable sudo access to members of the admin group. SEE ALSO
sudo(8), https://wiki.ubuntu.com/RootSudo February 8, 2006 sudo_root(8)
All times are GMT -4. The time now is 12:57 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy