Can not recognize network adapter SCO UNIX in HP z400
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
Code:
show message :
dlpid:unable to open network adapter driver (/dev/mid/r9e0)
dlpid: no such file or directory
please Help me .
tanks
Moderator's Comments:
Please use CODE tags, as required by forum rules, when displaying sample input, sample output, and code segments.
Last edited by Don Cragun; 10-30-2016 at 04:57 AM..
Reason: Add CODE and ICODE tags.
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT NETBSD
lo
LO(4) BSD Kernel Interfaces Manual LO(4)NAME
lo -- software loopback network interface
SYNOPSIS
pseudo-device loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
The loopback interface lo0 is created at boottime, it always exists and cannot be destroyed with ifconfig(8). Additional loopback interfaces
can be created by using the ifconfig(8) create command.
DIAGNOSTICS
lo%d: can't handle af%d . The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO inet(4), intro(4), ifconfig(8)HISTORY
The lo device appeared in 4.2BSD.
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
BSD September 3, 2006 BSD
10-30-2016
