Trying to mount a drive which has been dropped after corruption.
What is the quickets and esiest command to run and which switches? cheers
olly (1 Reply)
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
I'm trying to mount tape drive so I can tar from a cd.
this is what i type: mount /dev/rsd2940.4 /mnt
this is what i get: mount /dev/rsd2940.4 on /mnt : Block device required
I have no idea what that is supposed to mean. It's my understanding that rsd2940.4 is the block device. An... (1 Reply)
Hi,
Would appreciate if anyone could tell me if it is possible to mount (and use) a remote tape drive on a AIX server, and if so, what are the precise configuration steps needed?
The tape drive to be mounted as a remote tape drive is present on another AIX server in the same network.
... (0 Replies)
Hi,
Would appreciate if anyone could tell me if it is possible to mount (and use) a remote tape drive on a AIX server, and if so, what are the precise configuration steps needed?
The tape drive to be mounted as a remote tape drive is present on another AIX server in the same network.
... (5 Replies)
Hi there: I'm new here
Can anyone help me:
I have DS15 Alpha server : Unix 5.1B
Now i need to connect a DLVT VS80 1U Rackmount Tape Drive unit.
What is the exact comman to mount the DLTape IV??
How do i make backuo @ copy file to the tape?
Thanx to all (0 Replies)
Dear all,
I have a AIX server with logical 3 partitions and the server is connecting a tape drive. the first partition can successfully making a system backup to the tape but how can i fail to mount the tape to second and thrid partition. would anyone can help me to deal with it? what command... (3 Replies)
Discussion started by: rickhlwong
3 Replies
LEARN ABOUT DEBIAN
trm
TRM(4) BSD Kernel Interfaces Manual TRM(4)NAME
trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device trm
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
trm_load="YES"
DESCRIPTION
The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC.
HARDWARE
SCSI controllers supported by the trm driver include:
o Tekram DC-315 PCI Ultra SCSI adapter without BIOS and internal SCSI connector
o Tekram DC-315U PCI Ultra SCSI adapter without BIOS
o Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector
o Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS
o Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS
o Tekram DC-395U2W PCI Ultra2-Wide SCSI adapter with flash BIOS
For the Tekram DC-310/U and DC-390F/U/UW/U2B/U2W/U3W PCI SCSI host adapters, use the sym(4) driver.
SEE ALSO cd(4), ch(4), da(4), intro(4), sa(4), scsi(4), sym(4)
http://www.tekram.com/
AUTHORS
The trm driver was originally written for FreeBSD 3.0/i386 by Erich Chen of Tekram Technology, and ported to FreeBSD 5.0 by Olivier Houchard
<cognet@FreeBSD.org>.
BSD December 8, 2002 BSD