DNSTOP(8)						    BSD System Manager's Manual 						 DNSTOP(8)

NAME

     dnstop -- displays various tables of DNS traffic on your network

SYNOPSIS

     dnstop [-46apsQR] [-b expression] [-i address] [-f filter] [-r interval] [device] [savefile]

DESCRIPTION

     dnstop is a small tool to listen on device or to parse the file savefile and collect and print statistics on the local network's DNS traffic.
     You must have read access to /dev/bpf*.

COMMAND LINE OPTIONS

     The options are as follows:

     -4      count only messages with IPv4 addresses

     -6      count only messages with IPv6 addresses

     -Q      count only DNS query messages

     -R      count only DNS reply messages

     -a      anonymize addresses

     -b expression
	     BPF filter expression
	     (default: udp port 53)

     -i address
	     ignore select addresses

     -p      Do not put the interface into promiscuous mode.

     -r      Redraw interval (seconds).

     -l level
	     keep counts on names up to level domain name levels.

	     For example, with -l 2 (the default), dnstop will keep two tables: one with top-level domain names, and another with second-level
	     domain names.  Increasing the level provides more details, but also requires more memory and CPU.

     -f      input filter name

	     The "unknown-tlds" filter includes only queries for TLDs that are bogus.  Useful for identifying hosts/servers that leak queries for
	     things like "localhost" or "workgroup."

	     The "A-for-A" filter includes only A queries for names that are already IP addresses.  Certain Microsoft Windows DNS servers have a
	     known bug that forward these queries.

	     The "rfc1918-ptr" filter includes only PTR queries for addresses in RFC1918 space.  These should never leak from inside an organiza-
	     tion.

	     The "refused" filter, when used with the -R option, tells dnstop to count only replies with rcode REFUSED.

	     The "qtype-any" filter tells dnstop to count only message of type ANY.

     -n name
	     Only count messages within the domain name

     -P      Print "progress" messages on stderr when in non-interactive mode.

     -B buckets
	     Use buckets hash table buckets.

     -X      Do not tabulate the sources + query name counters.  This can significantly reduce memory usage on busy servers and large savefiles.

     savefile
	     a captured network trace in pcap format

     device  ethernet device (ie fxp0)

RUN TIME OPTIONS

     While running, the following options are available to alter the display:

     s	     display the source address table

     d	     display the destination address table

     t	     display the breakdown of query types seen

     r	     display the breakdown of response codes seen

     o	     display the breakdown of opcodes seen

     1	     show 1st level query names

     2	     show 2nd level query names

     3	     show 3rd level query names

     4	     show 4th level query names

     5	     show 5th level query names

     6	     show 6th level query names

     7	     show 7th level query names

     8	     show 8th level query names

     9	     show 9th level query names

     !	     show sources + 1st level query names

     @	     show sources + 2nd level query names

     #	     show sources + 3rd level query names

     $	     show sources + 4th level query names

     %	     show sources + 5th level query names

     ^	     show sources + 6th level query names

     &	     show sources + 7th level query names

     *	     show sources + 8th level query names

     (	     show sources + 9th level query names

     ^R      reset the counters

     ^X      exit the program

     space   redraw

     ?	     help

NON-INTERACTIVE MODE
     If stdout is not a tty, dnstop runs in non-interactive mode.  In this case, you must supply a savefile for reading, instead of capturing live
     packets.  After reading the entire savefile, dnstop prints the top 50 entries for each table.

HOW MESSAGES ARE COUNTED

     By default dnstop examines only query messages and ignores replies.  In this case the response code table is meaningless and will likely show
     100% "Noerror."

     If you supply (only) the -R command line option, dnstop examines replies and ignores queries.  This allows you to see meaningful response
     code values, as well as all the other tables.  In this case all the query attributes (such as type and name) are taken from the Question sec-
     tion of the reply.

     Note, however, that it is common for a stream of DNS messages to contain more queries than replies.  This could happen, for example, if the
     server is too busy to respond to every single query, or if the server is designed to ignore malformed query messages.  Therefore, you might
     want to examine both queries and replies by giving both -R and -Q command line options.  In this case, only the response code counts are
     taken from the replies and all other attributes are taken from the queries.

AUTHORS

     Duane Wessels (wessels@measurement-factory.com)
     Mark Foster (mark@foster.cc)
     Jose Nazario (jose@monkey.org)
     Sam Norris <@ChangeIP.com>
     Max Horn <@quendi.de>
     John Morrissey <jwm@horde.net>
     Florian Forster <octo@verplant.org>
     Dave Plonka <plonka@cs.wisc.edu>
     http://dnstop.measurement-factory.com/

BUGS

     Does not support TCP at this time.

BSD
								  21 March, 2008							       BSD