07-16-2015
what o/s and what route command are you entering; also, what does netstat -rn show, what does netstat -in show; show the traceroute command you used
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am trying to add a route for an interface on my unix server. The interface is qfe0. How do I type out the route add command.
The Normal way is
route add 1.1.1.0 1.1.1.1
When I want it to bind to a certain interface how to I enter the command. (1 Reply)
Discussion started by: Hordak
1 Replies
2. IP Networking
I am running SCOUnix OpenServer 5.0.5. For some reason a route in my routing table is being deleted and I do not know why. As far as I can see, it is nothing obvious that is deleting the route. The rest of the table is fine, only one particular entry is being delete. I run S99routes to reestablish... (3 Replies)
Discussion started by: walkerd810
3 Replies
3. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
4. UNIX for Dummies Questions & Answers
I not able to ping outside the internet. i am able to ping my 192. ip address. when i try to ping a 68. ip address i get no route to host. what should i do to correct this issue. I have sco openserver 5.05 (6 Replies)
Discussion started by: scoman2
6 Replies
5. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
6. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Request you to please tell me the command or the process to add the static route in redhat linux.
Thanks in Advance.
Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
8. IP Networking
Hi,
HP-UX 11iV2, but it's probably universal (tcp/ip)
I have a production and a test server. The test server gets the application updated nightly from the production server software. The application accesses a set of process servers on a separate subnet (192.163.22.30,31,32), but reachable... (1 Reply)
Discussion started by: monroedoug
1 Replies
9. Red Hat
I get below error when using telnet and ssh ??
Why ? the ip address of linux server is 10.155.25.22 =tstgcota ??
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.75.0 0.0.0.0 255.255.255.0 U 0 0... (6 Replies)
Discussion started by: chuikingman
6 Replies
10. Shell Programming and Scripting
OS : *NIX
Shell : any
I want to test telnet for a certain port on a certain machine, but via a VIP which is in front of that machine. Basically I want to follow the same route as the application does. Is there any possiblility to force telnet to follow a certain route (via the VIP I mentioned)... (2 Replies)
Discussion started by: black_fender
2 Replies
LEARN ABOUT PLAN9
tc-route
Route classifier in tc(8) Linux Route classifier in tc(8)
NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO
tc(8), ip-route(8)
iproute2 21 Oct 2015 Route classifier in tc(8)