06-13-2015
Have done changing cables but not helping....thanks a lot ....
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
when installing a piece of third part software I get the error "Bad magic number" at one point when it tries to use libraries from the bea tuxedo server. Am I correct that this means that the software is expecting 32bit while I'm on 64bit? Is there a way around it or can it only be solved... (5 Replies)
Discussion started by: rein
5 Replies
2. Solaris
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies
3. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
4. UNIX for Advanced & Expert Users
Hello All,
(RHEL4)
Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array.
I somehow managed to up the system with working raid1 array.
But the main problem persisted..
i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies
5. Solaris
Hello All,
I m very new to this forum.
i m having SUN NETRA X1 server with 40 GB HDD (Seagate) & 128 MB RAM.
i m trying this server for SUN 10 Practise.
As i m installing SUN 9 /10 with CD ,its giving me error after OK propmt
***************************
#boot cdrom
or
#boot cdrom... (16 Replies)
Discussion started by: amrut_k
16 Replies
6. Solaris
Hello,
I'm brand new to Sun/Solaris.
I have a Sun Blade 150, with SunOS 5.8.
I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk... (6 Replies)
Discussion started by: Resadija
6 Replies
7. Solaris
I'll keep it fairly straight forward. I work with a Solaris server and magically today it decided to take a dump on me. At first it give a long list of files that couldn't be acessed before terminating the boot process and returning to the 'ok' prompt. Booting in single-user mode allowed me to run... (4 Replies)
Discussion started by: Aon
4 Replies
8. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
9. Solaris
Is there a way to recover label?
I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies
10. Solaris
So we have a new to us v240 server with no OS installed. It has an outdated version of OB and ALOM so before we install the OS we want to update both. We have a DVD with the latest OB patch burned on it.
We do the boot cdrom command but receive the Bad Magic Number Error. Does an OS need to... (2 Replies)
Discussion started by: dunkpancakes
2 Replies
LEARN ABOUT CENTOS
plipconfig
PLIPCONFIG(8) Linux System Administrator's Manual PLIPCONFIG(8)
NAME
plipconfig - fine tune PLIP device parameters
SYNOPSIS
plipconfig interface [nibble NN] [trigger NN]
plipconfig [-V] [--version] [-h] [--help]
DESCRIPTION
Plipconfig is used to (hopefully) improve PLIP performance by changing the default timing parameters used by the PLIP protocol. Results are
dependent on the parallel port hardware, cable, and the CPU speed of each machine on each end of the PLIP link.
If the single interface argument is given, plipconfig displays the status of the given interface only. Otherwise, it will try to set the
options.
OPTIONS
nibble NN
Sets the nibble wait value in microseconds. Default is 3000.
trigger NN
Sets the trigger wait value in microseconds. Default is 500.
PLIP speed can in some cases be improved by lowering the default values. Values which are too low may cause excess use of CPU, poor inter-
rupt response time resulting in serial ports dropping characters, or in dropping of PLIP packets. Changing the plip MTU can also affect
PLIP speed.
NOTE
If you get no response it is far more likely the irq is wrong and needs setting with ifconfig. The few cases where the default parameters
will be too fast are those using very long cables. Something you should never do as the parallel port is not specified or designed for
driving long cable runs.
SEE ALSO
ifconfig(8)
BUGS
Non.
AUTHOR
John Paul Morrison, <jmorriso@bogomips.ee.ubc.ca>, <ve7jpm@ve7jpm.ampr.org>
net-tools 2008-10-03 PLIPCONFIG(8)