03-04-2015
Sun Sparc Ultra 30 help
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can anyone help me troubleshooting what is failing?
Many thanks.
---------- Post updated at 01:20 AM ---------- Previous update was at 12:13 AM ----------
right.. I've managed to get video. I unscrewed the PSU and disconnected the small connector on the motherboard in order to check the ram. But I could not work out how to remove the ram and clean it. I then booted again and now shows...
---------- Post updated at 01:21 AM ---------- Previous update was at 01:20 AM ----------
It asks for a firmware password which I don't have
Any ideas?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies
2. UNIX for Advanced & Expert Users
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies
3. Solaris
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Discussion started by: tribbles
7 Replies
4. Solaris
In Sparc Ultra 45 machine, how to enable bge1 port, how to do if bge0 is down then bge1 should automatically up.
Thanks & Regards (2 Replies)
Discussion started by: durgaprasadr13
2 Replies
5. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
6. Debian
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies
7. Solaris
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies
8. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
9. Solaris
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies
10. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT OPENSOLARIS
sf880drd
sf880drd(1M) System Administration Commands sf880drd(1M)
NAME
sf880drd - Sun Fire 880 Dynamic Reconfiguration daemon
SYNOPSIS
sf880drd
DESCRIPTION
The Sun Fire 880 Dynamic Reconfiguration daemon, sf880drd, is part of the PCI and system bus hotplug framework. sf880drd starts at boot
time. It has no configuration options and does not report any system status.
sf880drd implements the Sun Fire 880 console-less system administration (per-slot pushbuttons and LED status indicators). It also manages
various aspects of CPU/memory hotplug.
FILES
/usr/platform/SUNW,Sun-Fire-880/lib/sf880drd
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsfdr.u |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), cfgadm(1M), cfgadm_pci(1M), cfgadm_sbd(1M), svcadm(1M), attributes(5), smf(5)
NOTES
The sf880drd service is managed by the service management facility, smf(5), under the service identifier:
svc:/platform/sun4u/sf880drd
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.11 13 Aug 2004 sf880drd(1M)