03-04-2015
Sun Sparc Ultra 30 help
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can anyone help me troubleshooting what is failing?
Many thanks.
---------- Post updated at 01:20 AM ---------- Previous update was at 12:13 AM ----------
right.. I've managed to get video. I unscrewed the PSU and disconnected the small connector on the motherboard in order to check the ram. But I could not work out how to remove the ram and clean it. I then booted again and now shows...
---------- Post updated at 01:21 AM ---------- Previous update was at 01:20 AM ----------
It asks for a firmware password which I don't have
Any ideas?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies
2. UNIX for Advanced & Expert Users
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies
3. Solaris
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Discussion started by: tribbles
7 Replies
4. Solaris
In Sparc Ultra 45 machine, how to enable bge1 port, how to do if bge0 is down then bge1 should automatically up.
Thanks & Regards (2 Replies)
Discussion started by: durgaprasadr13
2 Replies
5. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
6. Debian
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies
7. Solaris
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies
8. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
9. Solaris
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies
10. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT CENTOS
grub-render-label
GRUB-RENDER-LABEL(1) User Commands GRUB-RENDER-LABEL(1)
NAME
grub-render-label - generate a .disk_label for Apple Macs.
SYNOPSIS
grub-render-label [OPTION...] [OPTIONS]
DESCRIPTION
Render Apple .disk_label.
-b, --bgcolor=COLOR
use COLOR for background
-c, --color=COLOR
use COLOR for text
-f, --font=FILE
use FILE as font (PF2).
-i, --input=FILE
read text from FILE.
-o, --output=FILE
set output filename. Default is STDOUT
-t, --text=STRING
set the label to render
-v, --verbose
print verbose messages.
-?, --help
give this help list
--usage
give a short usage message
-V, --version
print program version
Mandatory or optional arguments to long options are also mandatory or optional for any corresponding short options.
REPORTING BUGS
Report bugs to <bug-grub@gnu.org>.
SEE ALSO
The full documentation for grub-render-label is maintained as a Texinfo manual. If the info and grub-render-label programs are properly
installed at your site, the command
info grub-render-label
should give you access to the complete manual.
grub-render-label (GRUB) 2.02-2ubuntu8.3 July 2018 GRUB-RENDER-LABEL(1)