Help needed HP UX 11.11i new install on C8000 Desktop messaging system error CAN'T FIX
Hi, I have a HP UX C8000 box , have installed 11.11i from 4 x cds numerous times to try to get a functioning Network or to try and get rid of this error on start up, after new install and 1st startup I get an error
and then advice about pressing ok to return to login and to login in a failsafe session and then check to see /etc/hosts that the network is properly configured. I enter failsafe login and run SAM and configure network and checked that Mozilla can access internet , it can, (although it keeps crashing and exits , it still can load webpages ok before crashing) but I cannot , for the life of me , work out how to configure desktop messaging system so that I can login to a normal (non failsafe) session, on searching for a solution
I found advice to try cp nsswitch.files nsswitch.conf I do this, and it fixes the error and I don't get the error on logging in BUT I then cannot access the internet , I can't work out how to remove this error AND retain internet access, any help would be greatly appreciated, Thanx
Hi People!
I've just got a HP-UX system dumped on me. I've started it, followed all the install/setup questions, and everything was going ok, right upto when going into the desktop enviroment I got the message "The Desktop Messaging System Could Not Be Started".
Now I've checked the... (8 Replies)
Hello folks, had a question.
I was trying to install sudotool on HP -UX 11i.
I downloaded gzip file from sudo site and unzipped to /tmp folder on HP box
how do i install it??
do i need to run "swinstall" menu and then choose from there?
THanks!
karthik (1 Reply)
Hi Experts
I have a C3000 workstation onto which I am trying to install 11i however I am running into the following error.
ENTRY_INIT failed, status = -4: Unrecoverable hardware error
(followed by a hex dump)
I have re-tried many times and on one occasion successfully got through to CD... (4 Replies)
Hey,
i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write
BOot P1
P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said:
P0 scsiA.6 HP73.4MAT3073NP
P1 ide.1 ... (2 Replies)
Hello All,
I am getting " The DT messaging system could not be started" message when wants to login as root on a box running on tru64 5.1A.
/etc/hosts is ok.
when i see in .dt/errorlog it shows message server could not be started.
Thanks for help.
Awadhesh (2 Replies)
hi all,
I want to install iplanet messaging service in solaris 10.
if it is possible plz send the procedure for installation.its urgent plz
regards
spandan (2 Replies)
Hi there,
hope you can help since I'm a novice and playing with this machine to maybe one day use it with our non-profit art project (plantage9.de).
I have the proper media for itanium and everything seems okay, loads the DVD etc., until it halts without any progress for hours (see also image... (1 Reply)
I have an application rpm which when installed is failing to get installed with error
error: Failed dependencies:
libc.so.6 is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.0) is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.1) is needed by testSam-4.7.x86_64
... (1 Reply)
Good Morning,
Users can no longer log into SunBlade 2500 Solaris 9 system (though root still can). Here's what I'm getting and what I've done. I'm most suspicious of the full drive since that pops up twice and I did see one looks full. What's a good way to reduce what's on it?- or.. what else... (2 Replies)