07-09-2014
I think I explained everything in my older posts... Please read everything carefully and come back if you still don't understand what is happening!
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I ;ve a SUN x4600 running solaris 10. I want to connect to the system remotely form console like we can connect to sparc sc or alom .. (9 Replies)
Discussion started by: fugitive
9 Replies
2. Solaris
I need to configure the iLOM for x4600 server. before I can set the IP details and commit, I need to set network state should be enabled. However my firmware is already the latest and I need not upgrade. I am not able to set the /SP/network state to enable. pls assist. i BELIEVE the bug was fixed... (5 Replies)
Discussion started by: incredible
5 Replies
3. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
4. Solaris
Hi Folks,
Has anyone seen these errors on bootup.
Mar 15 12:22:30 svc.startd: svc:/system/device/local:default: Method "/lib/svc/method/devices-local" failed due to signal SEGV.ht (c) 1983, 2010,
Oracle and/or its affiliates. All rights reserved.
Configuring devices. ... (1 Reply)
Discussion started by: ESSTEAM
1 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Solaris
I got a replacement Heatsink and Fan unit, but the OEM unit has the SUN Thermal Interface Material (TIM) already on the heatsink matting surface. Because mine is used it does not have the TIM. Also there are 2 different TIM material SUN used based on the Processor (1-1.28GHz uses a glue backed... (1 Reply)
Discussion started by: danneskjold0809
1 Replies
8. Hardware
Booting and checking BIOS there is no option to enable-disable hyperthreading.
I have 8 Dual-Core AMD Opteron(tm) Processor 8220 and I see 16 cores.
Enable hyperthreading I should have 32 cores.
I have red hat 5.4 installed.
Anyone know how can enable hypethreading ? I have last BIOS/Firmware... (2 Replies)
Discussion started by: laxtnog
2 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT FREEBSD
gsignal
PSIGNAL(9) BSD Kernel Developer's Manual PSIGNAL(9)
NAME
psignal, pgsignal, gsignal, tdsignal -- post signal to a thread, process, or process group
SYNOPSIS
#include <sys/types.h>
#include <sys/signalvar.h>
void
psignal(struct proc *p, int signum);
void
pgsignal(struct pgrp *pgrp, int signum, int checkctty);
void
gsignal(int pgid, int signum);
void
tdsignal(struct thread *td, int signum);
DESCRIPTION
These functions post a signal to a thread or one or more processes. The argument signum common to all three functions should be in the range
[1-NSIG].
The psignal() function posts signal number signum to the process represented by the process structure p. With a few exceptions noted below,
the target process signal disposition is updated and is marked as runnable, so further handling of the signal is done in the context of the
target process after a context switch. Note that psignal() does not by itself cause a context switch to happen.
The target process is not marked as runnable in the following cases:
o The target process is sleeping uninterruptibly. The signal will be noticed when the process returns from the system call or trap.
o The target process is currently ignoring the signal.
o If a stop signal is sent to a sleeping process that takes the default action (see sigaction(2)), the process is stopped without
awakening it.
o SIGCONT restarts a stopped process (or puts them back to sleep) regardless of the signal action (e.g., blocked or ignored).
If the target process is being traced psignal() behaves as if the target process were taking the default action for signum. This allows the
tracing process to be notified of the signal.
The pgsignal() function posts signal number signum to each member of the process group described by pgrp. If checkctty is non-zero, the sig-
nal will be posted only to processes that have a controlling terminal. pgsignal() is implemented by walking along the process list headed by
the field pg_members of the process group structure pointed at by pgrp and calling psignal() as appropriate. If pgrp is NULL no action is
taken.
The gsignal() function posts signal number signum to each member of the process group identified by the group id pgid. gsignal() first finds
the group structure associated with pgid, then invokes pgsignal() with the argument checkctty set to zero. If pgid is zero no action is
taken.
The tdsignal() function posts signal number signum to the thread represented by the thread structure td.
SEE ALSO
sigaction(2), signal(9), tsleep(9)
BSD
October 8, 2011 BSD