12-25-2013
Your question is not clear. Most servers have a single primary IP address. So, what does IPADDR2 refer to? A virtual (or zone)? An ISCSI SAN connection? We cannot guess and give decent answers.
Knowing the OS would help a lot.
10 More Discussions You Might Find Interesting
1. Solaris
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies
2. Linux
Hello everybody,
How can link network interface to the output of lspci -vv. Basicly i need to know who is the manufacturer of a specific interface, for example eth0 {Is it an Intel, or Broadcome, or something else}. Is there a way to find that out?
Thanx (5 Replies)
Discussion started by: aleksey
5 Replies
3. AIX
hi all,
how do i change the routing info and make sure i will be able to connect remotely?
any ideas please?
thanks in advance. (1 Reply)
Discussion started by: itik
1 Replies
4. IP Networking
Hi,
how can i sftp or scp between 2 servers, when only i am able to ping to them.
they are on different network
10.130.170.31 -- server 1
10.130.230.141 -- server 2
i need to transfer data files from 1 to 2.
need your suggestions or help on these.
Regards
saha (4 Replies)
Discussion started by: saha
4 Replies
5. Shell Programming and Scripting
Hey guys,
I just started college a few days ago. To my dismay, my school has a very frustrating wireless network access system. Every time you want to use the network, you need to open up a browser and get re-directed to a login page. Every access, you need to reenter the same username and... (1 Reply)
Discussion started by: Chain Breaker
1 Replies
6. UNIX for Dummies Questions & Answers
Hello,
is there any tool where I can scan my netwrk and get all types of Unix servers? (2 Replies)
Discussion started by: fsmadi
2 Replies
7. UNIX and Linux Applications
In gnome there was an indicator applet that displayed your ip address, subnet mask, gateway, and dns. Is there a similar applet in kde? (0 Replies)
Discussion started by: cokedude
0 Replies
8. UNIX for Advanced & Expert Users
Is there a command that display all network info. I'm looking for ip address, subnet mask, gateway, and dns. If there isn't a single command could someone please write me a shellscript that can do this? (8 Replies)
Discussion started by: cokedude
8 Replies
9. UNIX for Advanced & Expert Users
Hi,
I'm trying to figure out how much traffic has been generated and received from netstat -s output (using Linux). I can see the output shows packet counts and Octet values, how would I correctly calculate how much traffic in and how much out?
My output below:
Ip:
88847576 total... (1 Reply)
Discussion started by: wilsonee
1 Replies
10. Shell Programming and Scripting
Hi,
I want to collect info from a no. of servers whether there grub.conf contain "elevator" parameter or not.
What I want is
sudo cat /etc/grub.conf | grep -q "elevator=noop"; echo $?
If output is "0", I want name of that host in a file called "present"
if its not "0", I want that... (4 Replies)
Discussion started by: stunn3r
4 Replies
bssh/bvnc/bshell(1) General Commands Manual bssh/bvnc/bshell(1)
NAME
bssh/bvnc/bshell - Browse for SSH/VNC servers on the local network
SYNOPSIS
bssh
bvnc
bshell
DESCRIPTION
bssh/bvnc/bshell browses for SSH/VNC servers on the local network, shows them in a GUI for the user to select one and finally calls
ssh/vncviewer after a selection was made.
If the binary is called as bssh only ssh servers will be shown. If the binary is called as bvnc only VNC servers will be shown. If the
binary is called as bshell both VNC and SSH servers are shown.
OPTIONS
-s | --ssh
Browse for SSH servers (and only SSH servers) regardless under which name the binary is called.
-v | --vnc
Browse for VNC servers (and only VNC servers) regardless under which name the binary is called.
-S | --shell
Browse for both VNC and SSH servers regardless under which name the binary is called.
-d | --domain= DOMAIN
Browse in the specified domain. If omitted bssh/bvnc/bshell will browse in the default browsing domain (usually .local)
-h | --help
Show help.
AUTHORS
The Avahi Developers <avahi (at) lists (dot) freedesktop (dot) org>; Avahi is available from http://avahi.org/
SEE ALSO
avahi-browse(1), ssh(1), vncviewer(1)
COMMENTS
This man page was written using xml2man(1) by Oliver Kurth.
Manuals User bssh/bvnc/bshell(1)