Sponsored Content
Operating Systems SCO How to change raid controller driver ? (hardware change) Post 302875173 by jgt on Monday 18th of November 2013 05:41:01 PM
Old 11-18-2013
As a note of explanation, this procedure applies only to host bus adapters, not RAID controllers such as the Mylex DAC960.
Also when the host bus adapter is changed, the new adapter may not see the drive with the same geometry, so it may be necessary to use the 'biosgeom' boot string, and then run 'dparam' to make the change permanently.
This User Gave Thanks to jgt For This Post:
 

10 More Discussions You Might Find Interesting

1. IP Networking

Ip Addresses With Hardware Change

I have 2 identical printers with the same IP on my network. One is only used as a backup for the primary printer and both are never on line at the same time. The goal was to always keep only 1 on and have an use the other printer as an immediate backup if necessary. But when I switch the cable I... (4 Replies)
Discussion started by: golfs4us
4 Replies

2. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon (1 Reply)
Discussion started by: karzon
1 Replies

3. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

4. UNIX for Dummies Questions & Answers

Samba change domain controller

Hello people i have a samba and they changed domain controller from a windows 2003 to a windows 2008, there is a problem with the version of samba maybe incompatibilities i dont know what show me this domain_client_validate: unable to validate password for user xxxx in domain xxxx to Domain... (0 Replies)
Discussion started by: enkei17
0 Replies

5. SCO

Change Disk controller in SCO 6.0.0

So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller. First, I downloaded the megasas driver from SCO and installed it on the old system. Then I created a new Microlite Edge emergency boot cd with the new driver on it. I... (2 Replies)
Discussion started by: jgt
2 Replies

6. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

7. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

8. IP Networking

C - IP change during a hardware refresh?

Hi All, I was told to perform analysis for IP change during a hardware refresh? Does the IP change when a hardware refresh is performed? if Yes, why? (5 Replies)
Discussion started by: visitsany
5 Replies

9. Linux

How to change ODBC Driver Manager?

Hi Forum. I have been searching this information for a while but to no avail. I'm running the following command odbcinst -j on a Linux box and get the following: unixODBC 2.3.0 DRIVERS............: //opt/Progress/DataDirect/Connect64_for_ODBC_71/odbcinst.ini SYSTEM DATA SOURCES:... (2 Replies)
Discussion started by: pchang
2 Replies

10. SCO

SCO OS 6 Driver for LSIL SAS1064E Raid Controller

Hi all, A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password. Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore. I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
SIISATA(4)						   BSD Kernel Interfaces Manual 						SIISATA(4)

NAME
siisata -- Silicon Image SATA-II controllers driver SYNOPSIS
siisata* at pci? dev ? function ? siisata* at cardbus? function ? DESCRIPTION
The siisata driver supports the Silicon Image SteelVine family of SATA-II controllers, interfacing the hardware with the ata(4) and atapi(4) subsystems. The following controllers are supported by the siisata driver: Silicon Image SiI3124 4-port PCI/PCI-X Silicon Image SiI3132 2-port PCI-Express x1 Silicon Image SiI3531 1-port PCI-Express x1 SEE ALSO
ata(4), atapi(4), cardbus(4), pci(4), wd(4) HISTORY
The siisata driver first appeared in NetBSD 5.0. AUTHORS
The siisata driver was written by Jonathan A. Kollasch <jakllsch@kollasch.net>. BUGS
SATA Native Command Queuing is not yet supported. Device hot swapping is not yet supported. Silicon Image's Software RAID is not yet supported by the ataraid(4) driver. raid(4) can be used instead. BSD
July 19, 2009 BSD
All times are GMT -4. The time now is 04:51 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy