Sponsored Content
Special Forums Hardware Sun Oracle Netra T5220 processor help Post 302849821 by nerdboy on Tuesday 3rd of September 2013 11:55:06 AM
Old 09-03-2013
Okay this is where I can get now. The cable change worked like a charm.

Code:
U-Boot 1.1.1

custom Sun Microsystems U-Boot 1.3 (May 13 2010 - 14:43:39) r55739

CPU:   MPC885ZPnn at 133 MHz: 8 kB I-Cache 8 kB D-Cache FEC present
Board: SPARC885
       Watchdog enabled
I2C:   ready
DRAM:
trying 128 MBytes
(128 MB SDRAM) 128 MB
Memory Tests: DA A1 A2 00 FF 55 AA T2 T3 T4
POST memory PASSED
FLASH: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   FEC ETHERNET
POST i2c  c  d 14 18 23 2a 2d 2e 30 40 43 46 51 53 54 56 59 68 69 6a 6b 70 71 PASSED
POST cpu PASSED
POST ethernet PASSED
Booting linux in 5 seconds...
## Booting image at fe080000 ...
   Image Name:   Linux-2.4.22
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    815098 Bytes = 796 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
do_bootm_linux():
  argv[0]=bootm
  argv[1]=0xfe080000
## Current stack ends at 0x07D38B60 => set upper limit to 0x00800000
No initrd
## cmdline at 0x007FFF00 ... 0x007FFF80
memstart    = 0x00000000
memsize     = 0x08000000
flashstart  = 0xFE000000
flashsize   = 0x02000000
flashoffset = 0x0004C000
sramstart   = 0x00000000
sramsize    = 0x00000000
EnvAddr     = 0xFFFFE2EE
EnvSize     = 0xBEF3EBFE
banksize    = 0x02000000
banks       = 0x00000001
bankwidth   = 0x00000001
sectorsize  = 0x00020000
sectorcount = 0x00000100
booted      = 0xFE080000
boottype    = 0x00000000
primary     = 0xFFFFFFFF
pritype     = 0x00000000
secondary   = 0xFFFFFFFF
sectype     = 0x00000000
image0      = 0xFE000000
image1      = 0xFF000000
maximage    = 0x01000000
immr_base   = 0xF0000000
bootflags   = 0x00000001
intfreq     =    133 MHz
busfreq     = 66.500 MHz
ethaddr     = 00:21:28:D2:7C:47
IP addr     = 0.0.0.0
baudrate    =   9600 bps
## Transferring control to Linux (at address 00000000) ...
## parameters(007ffe80,00000000,00000000,007fff00,007fff80)
Linux version 2.4.22 (cb75630@sanpen-rh5-3) (gcc version 3.3.4) #2 Thu May 13 14:39:31 PDT 2010 r55905
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock4 rootfstype=squashfs ro mtdparts=phys:384K(u1),128k(e1),1536K(k1),14M(r1),384K(u2),128K(e2),1536K(k2),14M(r2)
Decrementer Frequency = 498750000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger

U-Boot 1.1.1

custom Sun Microsystems U-Boot 1.3 (May 13 2010 - 14:43:39) r55739

CPU:   MPC885ZPnn at 133 MHz: 8 kB I-Cache 8 kB D-Cache FEC present
Board: SPARC885
       Watchdog enabled
I2C:   ready
DRAM:
trying 128 MBytes
(128 MB SDRAM) 128 MB
FLASH: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   FEC ETHERNET
POST i2c  c  d 14 18 23 2a 2d 2e 30 40 43 46 51 53 54 56 59 68 69 6a 6b 70 71 PASSED
POST cpu PASSED
POST ethernet PASSED
Booting linux in 5 seconds...
## Booting image at fe080000 ...
   Image Name:   Linux-2.4.22
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    815098 Bytes = 796 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
do_bootm_linux():
  argv[0]=bootm
  argv[1]=0xfe080000
## Current stack ends at 0x07D38B60 => set upper limit to 0x00800000
No initrd
## cmdline at 0x007FFF00 ... 0x007FFF80
memstart    = 0x00000000
memsize     = 0x08000000
flashstart  = 0xFE000000
flashsize   = 0x02000000
flashoffset = 0x0004C000
sramstart   = 0x00000000
sramsize    = 0x00000000
EnvAddr     = 0xFFFFE2EE
EnvSize     = 0xBEF3EBFE
banksize    = 0x02000000
banks       = 0x00000001
bankwidth   = 0x00000001
sectorsize  = 0x00020000
sectorcount = 0x00000100
booted      = 0xFE080000
boottype    = 0x00000000
primary     = 0xFFFFFFFF
pritype     = 0x00000000
secondary   = 0xFFFFFFFF
sectype     = 0x00000000
image0      = 0xFE000000
image1      = 0xFF000000
maximage    = 0x01000000
immr_base   = 0xF0000000
bootflags   = 0x00000001
intfreq     =    133 MHz
busfreq     = 66.500 MHz
ethaddr     = 00:21:28:D2:7C:47
IP addr     = 0.0.0.0
baudrate    =   9600 bps
## Transferring control to Linux (at address 00000000) ...
## parameters(007ffe80,00000000,00000000,007fff00,007fff80)
Linux version 2.4.22 (cb75630@sanpen-rh5-3) (gcc version 3.3.4) #2 Thu May 13 14:39:31 PDT 2010 r55905
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock4 rootfstype=squashfs ro mtdparts=phys:384K(u1),128k(e1),1536K(k1),14M(r1),384K(u2),128K(e2),1536K(k2),14M(r2)
Decrementer Frequency = 498750000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Calibrating delay loop... 132.71 BogoMIPS
Memory: 127624k available (1412k kernel code, 416k data, 68k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
squashfs: version 3.0 (2006/03/15) Phillip Lougher
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
CPM UART driver version 0.03
ttyS00 at 0x0100 is apty: 256 Unix98 ptys configured
Generic RTC Driver v1.07
WDT driver for MPC885 is registered.
eth0: FEC ENET Version 0.2, FEC irq 3, MII irq 6, addr 00:21:28:d2:7c:47
RAMDISK driver initialized: 16 RAM disks of 18432K size 1024 blocksize
eth0: Phy @ 0x0, type DM9161 (0x0181b881)
loop: loaded (max 8 devices)
physmap flash device: 2000000 at fe000000
 Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Using command line partition definition
Creating 8 MTD partitions on "Physically mapped flash":
mtdblock1: 0x00000000-0x00060000 : "u1"
mtdblock2: 0x00060000-0x00080000 : "e1"
mtdblock3: 0x00080000-0x00200000 : "k1"
mtdblock4: 0x00200000-0x01000000 : "r1"
mtdblock5: 0x01000000-0x01060000 : "u2"
mtdblock6: 0x01060000-0x01080000 : "e2"
mtdblock7: 0x01080000-0x01200000 : "k2"
mtdblock8: 0x01200000-0x02000000 : "r2"
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-rpx.o: i2c MPC8xx module version 2.6.1 (20010830)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
ip_conntrack version 2.1 (1024 buckets, 8192 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 68k init
modprobe: modprobe: Can't open dependencies file /lib/modules/2.4.22/modules.dep (No such file or directory)
Creating /var tmpfs
Creating directories in /var...done.
Creating /var/log tmpfs...done.
Activating swap.
Calculating module dependencies... done.
Loading modules...
    fpga
Warning: loading /lib/modules/2.4.22/misc/fpga/fpga.o will taint the kernel: non-GPL license - Proprietary
  See The linux-kernel mailing list FAQ for information about tainted modules
Platform ID      : 1
Minor revision   : 0
Major revision   : 5
FPGA power status : 80
  (SYS_POK_EN  !DC_POK  !POK_OIO  !POK_VMEMR  !POK_VMEML  !POK_VCORE  !POK_PSU1  !POK_PSU0 )
BR2: 0xf2000000/0x1000000/0xf2000401/0xff0001fc
FPGA init OK: base f2000000, size 1000000 (major 120)
Module fpga loaded, with warnings
    fpga_flash
Warning: loading /lib/modules/2.4.22/misc/fpga_flash/fpga_flash.o will taint the kernel: no license
  See The linux-kernel mailing list FAQ for information about tainted modules
Module fpga_flash loaded, with warnings
    immap
Warning: loading /lib/modules/2.4.22/misc/immap/immap.o will taint the kernel: no license
  See The linux-kernel mailing list FAQ for information about tainted modules
Module immap loaded, with warnings
All modules loaded.
Checking all file systems...
fsck (busybox 1.9.0, 2010-05-13 14:44:03 PDT)
Setting kernel variables ...
kernel.core_pattern = /coredump/%h.%e.core
kernel.core_uses_pid = 1
net.ipv4.ip_local_port_range = 3100 7075
... done.
Mounting local filesystems...
Identifying DOC Device Type(G3/G4/H3) ...



Warning: /lib/modules/2.4.22/misc/tffs/tffs_h3.o symbol for parameter prio not found
Warning: loading /lib/modules/2.4.22/misc/tffs/tffs_h3.o will taint the kernel: non-GPL license - Proprietary
  See The linux-kernel mailing list FAQ for information about tainted modules
tffs: TrueFFS driver 7100.76
tffs: will not use IRQ
tffs: Looking for G4/P4 MDOC Devices while assuming IF_CFG=16.
tffs: Looking for G4/P4 MDOC Devices while assuming IF_CFG=8.
tffs: Flow: G4_docWindowBaseAddress Exit (NOT FOUND).
tffs: Looking for G3/P3 MDOC Devices while assuming IF_CFG=16.
tffs: Looking for G3/P3 MDOC Devices while assuming IF_CFG=8.
tffs: Looking for H1 DOC at address 0xcd14e000
tffs: DOCH found
tffs: Socket 0 in addr 0xf4000000
tffs: Device 0x0: size 0x1db00000 HW sector 0x200 (recommended 0x1000)
tffs: use major device number 100
Partition check:
 tffsa: tffsa1 tffsa2 tffsa3
tffs:     disk partition: dev_number=0x6401, 65534 sectors, start_sector=1
tffs:     disk partition: dev_number=0x6402, 65536 sectors, start_sector=65535
tffs:     disk partition: dev_number=0x6403, 112000 sectors, start_sector=131071
Module tffs_h3 loaded, with warnings
Loaded TFFS kernel module /lib/modules/2.4.22/misc/tffs/tffs_h3.o
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on tffs(100,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,0), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on tffs(100,3), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Checking DOC size...
Mounted all disk partitions.

Checking configuration files state ...
Image date:  Thu May 13 15:57:50 PDT 2010       Image revision: 55739
Conf date:   Thu May 13 15:57:50 PDT 2010       Conf revision:  55739
Configuration files state good after upgrade.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Created links for vbsc
Running ldconfig...done
Hostname: SUNSP-gashost.

Setting the System Clock using the Hardware Clock as reference...
System Clock set. Local time: Mon Sep  2 23:46:32 GMT 2013

Setting up networking...done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces...done.
Starting portmap daemon: portmap.
Initializing random number generator...done.
Incrementing bootcount ... done (34)
Starting ILOM Watchdog daemon.
 Done
populating memstore vars from disk
Starting BBR daemon...
bbrd started after 1 seconds.
INIT: Entering runlevel: 3
Preparsing sensor.xml...
Starting system log daemon: syslogd and klogd.
Starting Boot Timer.
Starting user mgmt upgrade program: usrmgt_upgrade.
Starting the Health Monitor Daemon...
Starting portmap daemon: portmap.
Starting Network Interface Plugging Daemon: eth0.
Starting IPMI Stack...... Done.
SSH RSA Host Key Files already exist. Skipping key creation ...
SSH DSA Host Key Files already exist. Skipping key creation ...
OpenBSD Secure Shell server not in use (/etc/ssh/sshd_not_to_be_run)
Starting periodic command scheduler: cron.
Starting Serial Server :seriald .
Starting Servicetags discoverer: stdiscoverer.
State disabled
Starting Servicetags listener: stlistener.
State disabled

SUNSP-gashost login: root
Password:
Waiting for daemons to initialize...

.
Timed out waiting for daemons to start
sccd daemon has shutdown

Oracle(R) Integrated Lights Out Manager

Version 3.0.10.2.a r55739

Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved.

->

---------- Post updated at 10:55 AM ---------- Previous update was at 10:50 AM ----------

Last edited by nerdboy; 09-03-2013 at 02:39 PM..
 

10 More Discussions You Might Find Interesting

1. Solaris

Sun T5210 & T5220

Hi! Does anybody got some experiences with the Sun Server T5210 or T5220? -> especially in network configuration! Thanks... BYE (2 Replies)
Discussion started by: kaufmoa
2 Replies

2. Solaris

Sun Fire V1280 / E2900 / Netra 1280

Hello, I'm trying to fix this server System Board (CPU/Memory Unit). The error indicates that its missing 3.3VDC. So far all the fuses and caps have been checked. I new at this type of machine, need help for idea on this system. Thank you in advance. Vu (0 Replies)
Discussion started by: vhtran
0 Replies

3. Solaris

sun netra t1

so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll... (24 Replies)
Discussion started by: pupp
24 Replies

4. Solaris

Sun Netra T1 won't poweron/no POST

Hi guys. I have an old Netra T1 that I'm hoping to recover here so I can twiddle around with Solaris 10. It's been unable to power on despite issuing the "poweron" command or hitting the switch at the back of the server for some time. The LOM command "env" reports ALARM3 ON and everything else... (8 Replies)
Discussion started by: detach8
8 Replies

5. Solaris

SUN Netra 240 Boot error

Hi, When I am trying to boot my SUN Netra 240 Machine its giving some boot error. > {1} ok boot -i > Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i > Boot load failed. > The file just loaded does not appear to be executable. > {1} ok I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies

6. Solaris

Help size Netra T5220 to MAX

I have a new Netra T5220 that came preinstalled OS 10. The purpose is to be a backup server to store images of other Server Blades. There are three systems that will be storing their backups. Per engineering documents and with the vendor system it is determined that we needed somewhere around 300... (3 Replies)
Discussion started by: udubya
3 Replies

7. Hardware

Sun T5220 Firmware question

Hello all, I've been researching this to no avail, I have a T5220 running firmware 7.2.2.e (139442-06) However, the issue I have is that I want to update the firmware yet Oracle maintains 3 different sets of firmware for the T5220: 7.2.x = (139442-14) Being the latest at 7.2.11.a;... (4 Replies)
Discussion started by: seckure
4 Replies

8. Hardware

[solved] Sun Netra X1 - Adding a Second Hard Drive

As the title suggests, I'm trying to install a second drive (really want an OS mirror) on a Sun Netra X1. I've taken the spacer out, and had a go at with the drill-press so now I have a nice HDD tray. Have installed an IDE drive in the tray, plugged in the power and data cables that were... (0 Replies)
Discussion started by: Smiling Dragon
0 Replies

9. Solaris

SUn Netra X4200 M2 Drivers

Hi Guys, Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that? Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies

10. Solaris

I can't boot my Sun T5220 server from cdrom.

hi:) i can't boot my sun server by iso solaris 10 sparc dvd that i did download from oracle site. my hardware is sun T5220. i receive these after running boot cdrom -s : can't read disk lable can't open disk lable package ERROR: boot-read fail whould u help me? Please use CODE... (1 Reply)
Discussion started by: Arefdel
1 Replies
All times are GMT -4. The time now is 06:22 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy