07-25-2013
That worked. Thanks for your assistance.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi I was trying to mount my USB flashdrive on solaris 10 and I am getting the message saying that (I have already gone through the previous blogs in the forum)
mount: Block device required.
I have tried most of the possible ways.
#rmformat(gives me the necessary information about my flash... (1 Reply)
Discussion started by: akhil1460
1 Replies
2. Solaris
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
Discussion started by: sbk1972
9 Replies
3. UNIX for Dummies Questions & Answers
My previous post seems to be erased and I didn't get any help. I'm logged as root now but no mounting command seems to work, I've tried:
Mount -t vfat /dev/sdc1 /mnt/USB
Changing "sdc1" for hda1-7, and sdc1-7, and still nothing. Sometimes i get:
"special device not found" and others "device... (4 Replies)
Discussion started by: Dax01
4 Replies
4. Solaris
I am very new to Solaris.
The machine I am working with is running Solaris 10.
I have a 1.5 TB hard drive plugged into a USB dock plugged into the Solaris machine. I ran 'cfgadm -al' and can see that the usb0/1 is usb-storage that was not there before.
How do i mount this drive and format... (3 Replies)
Discussion started by: mcdef
3 Replies
5. Solaris
Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
exit
rebootxscf
logout
#.
#>
#>
~#
~#
exit
sendbreak
exit
I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies
6. Solaris
Hi,
I've configured this Sun M5000 to use two system domains (added a second domain to it). The following is the info about the settings. The showdevices command can't show devices on domain 1 because Solaris is not loaded on it yet.
My question: How can I confirm the hardware devices such as... (5 Replies)
Discussion started by: aixlover
5 Replies
7. Solaris
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Discussion started by: giles.cardew
6 Replies
8. Programming
Hi all,
I'm developing a short program to look-up for all devices connected to the computer. Using udev and libusb libraries I achieved some progress but I can not find the way to find the mount point.
For instance, given a device that I can retrieve using libusb, I would like to know... (4 Replies)
Discussion started by: Carles Rabaneda
4 Replies
9. Solaris
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
Discussion started by: badoshi
3 Replies
10. IP Networking
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
EHCI(4) BSD Kernel Interfaces Manual EHCI(4)
NAME
ehci -- USB Enhanced Host Controller driver
SYNOPSIS
device ehci
DESCRIPTION
The ehci driver provides support for the USB Enhanced Host Controller Interface, which is used by USB 2.0 controllers.
EHCI controllers are peculiar in that they can only handle the USB 2.0 protocol. This means that they normally have one or more companion
controllers (i.e., ohci(4) or uhci(4)) handling USB 1.x devices. Consequently each USB connector is electrically connected to two USB con-
trollers. The handling of this is totally automatic, but can be noticed since USB 1.x and USB 2.0 devices plugged in to the same connector
appear to connect to different USB busses.
SEE ALSO
ohci(4), uhci(4), usb(4)
HISTORY
The ehci device driver first appeared in FreeBSD 5.1.
BUGS
The driver is not finished and is quite buggy.
There is currently no support for isochronous transfers.
BSD March 20, 2005 BSD