05-03-2013
Turns out the issue was our old DVD. We had Solaris 10 dated 06/08. I downloaded the latest version this morning and now I can boot into Single User Mode and see the raid array. Thanks.
---------- Post updated at 10:58 AM ---------- Previous update was at 10:54 AM ----------
Event better news. Once in single user mode I activated the array by using raidctl -p state=activate <vol_id> and rebooted the server. Now it boots off the hard drives.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
Discussion started by: franruiz
3 Replies
2. Linux
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Discussion started by: tamcomng
2 Replies
3. Solaris
Version: solaris 10 x86
I just got a western digital external harddrive formated with fat 32. this drive came with some setup files which is meant for windows or mac.
I want to reformat and partition this drive into two ( for solaris and windows) such that the setup files will still be there... (2 Replies)
Discussion started by: seyiisq
2 Replies
4. Filesystems, Disks and Memory
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies
5. UNIX for Dummies Questions & Answers
Looking for some clues on how to set my internal hard drives inaccessible/busy to clonezilla. Noprobe doesn't work in startup and the drive is still found.
I know I can find all hard drives using the following:
sudo fdisk -l | grep GB | awk '{print $2}' | grep -Po "^+(?=:?)"
I tried... (9 Replies)
Discussion started by: traustic
9 Replies
6. Hardware
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
Discussion started by: Lost in Cyberia
3 Replies
7. Solaris
I have three Sun Oracle Netra T5220s. I am trying to just get the processor information psrinfo or prtdiag -v from the # prompt in single user mode.
I am needing to know the commands to get to boot the CD/DVD of the Solaris OS. I am using it via Serial Port Management.
Tinkering around I... (4 Replies)
Discussion started by: nerdboy
4 Replies
8. Linux
Hello,
I have install 2 HDD in my server and now installing the Centos6.4.
I want create the LVM of those 2 HDD's so while i'm doing this it is not allowing me to select these 2 disk's from allowable disk list.
Same problem if i tried to make Software RAID with creating LVM.
Please help. (1 Reply)
Discussion started by: purushottamaher
1 Replies
9. Solaris
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Discussion started by: ssabet
5 Replies
10. UNIX for Beginners Questions & Answers
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Discussion started by: cptkirkh
5 Replies
LEARN ABOUT OSX
set_color
set_color(1) fish set_color(1)
NAME
set_color - set_color - set the terminal color
set_color - set the terminal color
Synopsis
set_color [-v --version] [-h --help] [-b --background COLOR] [COLOR]
Description
Change the foreground and/or background color of the terminal. COLOR is one of black, red, green, brown, yellow, blue, magenta, purple,
cyan, white and normal.
o -b, --background Set the background color
o -c, --print-colors Prints a list of all valid color names
o -h, --help Display help message and exit
o -o, --bold Set bold or extra bright mode
o -u, --underline Set underlined mode
o -v, --version Display version and exit
Calling set_color normal will set the terminal color to whatever is the default color of the terminal.
Some terminals use the --bold escape sequence to switch to a brighter color set. On such terminals, set_color white will result in a grey
font color, while set_color --bold white will result in a white font color.
Not all terminal emulators support all these features. This is not a bug in set_color but a missing feature in the terminal emulator.
set_color uses the terminfo database to look up how to change terminal colors on whatever terminal is in use. Some systems have old and
incomplete terminfo databases, and may lack color information for terminals that support it. Download and install the latest version of
ncurses and recompile fish against it in order to fix this issue.
Version 1.23.1 Sun Jan 8 2012 set_color(1)