Hi,
I am using smitty to create and configure a print queue. I am giving a print of a text file to the print queue created. I am using this in network.
How to capture network packets of the print from AIX to the printer and printer to AIX.
I tried Wireshark to capture network packets.
I am... (16 Replies)
Hi,
I want to capture snmp packets in AIX.
When i give print from AIX6.1, Printer will give its response thru' snmp.
I used iptrace command like below, but it is not capturing snmp packets other packets are captured like udp, tcp..
1. iptrace command:
/usr/sbin/iptrace -a -i en0... (1 Reply)
Hi,
I want to capture a certain type of packets (selected according to the protocol) coming to my PC and then transmit them to another PC. I had the idea to use tcpdump to filter input packets and extract those chosen. Well my questions are:
1- after filtering input packets, those that have not... (1 Reply)
Hello
I try to send DHCP RENEW packets to the network and receive the responses. I broadcast the packet and I can see that it's successfully sent using Wireshark. But I have difficulties receiving the responses.I use packet sockets to catch the packets. I can see that there are responses to my... (0 Replies)
Hi, I have got sample linux driver written in C.
I got also some assembly code, compiled into .o file (using as compiler).
In my Makefile I got:
obj-m += someDriver.o
someDriver-objs := CFile1.o CFile2.o ASMFile.o
default:
$(MAKE) -C $(KDIR) SUBDIRS=$(PWD) modulesUnfortunatelly I cannot... (0 Replies)
Hi,
Its been a long time since i programmed a multithreaded application that can do Tx and Rx of datagrams over unix sockets.
I well remember that though the threads were efficiently designed to be independent of each other, and was writing to different sockets, there was a limitation ,... (0 Replies)
Discussion started by: binnyjeshan
0 Replies
LEARN ABOUT DEBIAN
if_faith
FAITH(4) BSD Kernel Interfaces Manual FAITH(4)NAME
faith -- IPv6-to-IPv4 TCP relay capturing interface
SYNOPSIS
device faith
DESCRIPTION
The faith interface captures IPv6 TCP traffic, for implementing userland IPv6-to-IPv4 TCP relay like faithd(8).
Each faith interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using
the cloned_interfaces variable in rc.conf(5).
Special action will be taken when IPv6 TCP traffic is seen on a router, and the routing table suggests to route it to the faith interface.
In this case, the packet will be accepted by the router, regardless of the list of IPv6 interface addresses assigned to the router. The
packet will be captured by an IPv6 TCP socket, if it has the IN6P_FAITH flag turned on and matching address/port pairs. As a result, faith
will let you capture IPv6 TCP traffic to some specific destination addresses. Userland programs, such as faithd(8) can use this behavior to
relay IPv6 TCP traffic to IPv4 TCP traffic. The program can accept some specific IPv6 TCP traffic, perform getsockname(2) to get the IPv6
destination address specified by the client, and perform application-specific address mapping to relay IPv6 TCP to IPv4 TCP.
The IN6P_FAITH flag on a IPv6 TCP socket can be set by using setsockopt(2), with level IPPROTO_IPV6 and optname IPv6_FAITH.
To handle error reports by ICMPv6, some ICMPv6 packets routed to an faith interface will be delivered to IPv6 TCP, as well.
To understand how faith can be used, take a look at the source code of faithd(8).
As the faith interface implements potentially dangerous operations, great care must be taken when configuring it. To avoid possible misuse,
the sysctl(8) variable net.inet6.ip6.keepfaith must be set to 1 prior to using the interface. When net.inet6.ip6.keepfaith is 0, no packets
will be captured by the faith interface.
The faith interface is intended to be used on routers, not on hosts.
SEE ALSO inet(4), inet6(4), faithd(8)
Jun-ichiro itojun Hagino and Kazu Yamamoto, An IPv6-to-IPv4 transport relay translator, RFC3142.
HISTORY
The FAITH IPv6-to-IPv4 TCP relay translator first appeared in the WIDE hydrangea IPv6 stack.
BSD April 10, 1999 BSD