12-28-2012
Thanks for the help! I have thought about the boot block maybe not being installed on the second drive. I thought with mirroring the boot block would be on the second drive because after all the root drive has the boot block installed so this would be replicated over to the second mirrored disk. I did not want to make it worse by running the installboot command. Also with the error messages showing /etc/inittab truncated or corrupted...this does not sound like a boot block issue?
The last file executed before the system boots up is /etc/inittab so does that mean the boot block was successfully executed if I coem to the ok prompt?
I am stil not able to figure out why we are getting this error on the /etc/inittab execution. If you have any ideas please throw them out!
I am trying to locate a Solaris 8 boot cdrom and try to boot in single user mode and copy over the default /etc/inittab file and see if this helps.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
So last week I posted about my system that will not completely boot. It reports a bad trap and reboots in an endless cycle. I'm at a point where I just want to wipe the system clean, reload the software and basically start from scratch.
I can interrupt the boot cycle and get to an ok prompt.... (2 Replies)
Discussion started by: forbin24
2 Replies
2. Solaris
Hi
Im using a Sun blade 1500 with solaris 8 and when the monitor goes to stand by mode, the machine doesnt return to the normal mode anymore. Then i have to reboot it always.
Does anybody have a clue how can i solve it or turn off the stand by mode?
Thanks (2 Replies)
Discussion started by: dougpss
2 Replies
3. UNIX for Dummies Questions & Answers
Hello to all!
In the OK prompt, which command should I use to see RAM memory, CPU, and disks partition and capacity?
I have in my hands an ancient Ultra5 machine, which Im trying to install Solaris, but don't know if the configuration is the original one.
Thanks! (4 Replies)
Discussion started by: Pablo_BR
4 Replies
4. Programming
Suppose that I have some data:
12,30
12,45
2,3
7,8
3,9
30, 8
45,54
56,65
Where (a,b) indicates that a is connected to b. I want to get all connected nodes to one point. For instance, the output of the above
example should be something like:
Group 1
2,3
3,9
Group 2
12,30
12,45... (4 Replies)
Discussion started by: Legend986
4 Replies
5. Solaris
Hi.
I got this message in our sun station and it stuck
Setting default IPv4 interface for multicast: add net 224.0/4: gateway pecsun22
but i can still telenet the station...
who could i fix this..
appreciate your help (7 Replies)
Discussion started by: eykyn17
7 Replies
6. Solaris
Hi all,
I was wondering how to change the PS1 to my liking?
I tried changing it using PS1='my choice'
it worked but the subsequent terminals i open will not have it as the default PS1 ,how do i change it?
also i am running as super user, and i need to exec bash, to get the bash environment...... (4 Replies)
Discussion started by: wrapster
4 Replies
7. Solaris
Hi,
Due to some changes at our company, we lost the password for the root and sms-svc account on the primary system controller (E25K).
We connected a serial console to the system controller but we never managed to break the session to bring it to the OK prompt.
(tried: ~#, ~ b, ~, , a b,... (9 Replies)
Discussion started by: Solarius
9 Replies
8. Solaris
Hi All,
I got a big problem here.
While setting up a sun cluster, I accidentally tried out "bootadm update-archive" as I was unable to bring the cluster up.
After which, i tried a reconfiguration reboot.
Now The system is always booting into maintanence mode with error message... (8 Replies)
Discussion started by: manojsomanath
8 Replies
9. UNIX for Dummies Questions & Answers
how to Change the % prompt to - prompt in unix
:wall:
---------- Post updated at 07:40 AM ---------- Previous update was at 07:38 AM ----------
How To display the last modification time of any file in unix
---------- Post updated at 07:40 AM ---------- Previous update was at 07:40 AM... (2 Replies)
Discussion started by: manjiri sawant
2 Replies
10. Solaris
Hi,
on sunfire v890 unable to move from rsc prompt to ok prompt, i have executed the command break. (9 Replies)
Discussion started by: manoj.solaris
9 Replies
LEARN ABOUT FREEBSD
boot.config
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)
NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO
boot(8), loader(8)
AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD
May 13, 2007 BSD