SG_VPD(8)							     SG3_UTILS								 SG_VPD(8)

NAME

       sg_vpd - fetches Vital Product Data (VPD) pages using a SCSI INQUIRY command

SYNOPSIS

       sg_vpd [--enumerate] [--help] [--hex] [--ident] [--long] [--maxlen=LEN] [--page=PG] [--quiet] [--raw] [--verbose] [--version] DEVICE

DESCRIPTION

       This  utility  fetches  a Vital Product Data page and decodes it or outputs it in ASCII hexadecimal or binary. VPD pages are fetched with a
       SCSI INQUIRY command.

       Probably the most important page is the Device Identification VPD page (page number: 0x83). Since SPC-3, support for  this  page  has  been
       flagged as mandatory. This page can be fetched by using the --ident option.

       When no options are given, other than a DEVICE, then the "Supported VPD pages" (0x0) VPD page is fetched and decoded.

OPTIONS

       Arguments to long options are mandatory for short options as well.  The options are arranged in alphabetical order based on the long option
       name.

       -e, --enumerate
	      list the names of the known VPD pages, first the standard pages, then the vendor specific pages. Each group is sorted  in  abbrevia-
	      tion order. The DEVICE and other options are ignored and this utility exits after listing the VPD page names.

       -h, --help
	      outputs the usage message summarizing command line options then exits.  Ignores DEVICE if given.

       -H, --hex
	      outputs the requested VPD page in ASCII hexadecimal. Can be used multiple times, see section on the ATA information vpd page.

       -i, --ident
	      decode the device identification (0x83) VPD page. When used once this option has the same effect as '--page=di'. When use twice then
	      the short form of the device identification VPD page's logical unit designator is decoded. In the latter case this  option  has  the
	      same effect as '--quiet --page=di_lu'.

       -l, --long
	      when  decoding some VPD pages, give a little more output. For example the ATA Information VPD page only shows the signature (in hex)
	      and the IDENTIFY (PACKET) DEVICE (in hex) when this option is given.

       -m, --maxlen=LEN
	      where LEN is the (maximum) response length in bytes. It is placed in the cdb's "allocation length" field. If not given  (or  LEN	is
	      zero)  then 252 is used (apart from the ATA Information VPD page which defaults to 572) and, if the response indicates this value is
	      insufficient, another INQUIRY command is sent with a larger value in the cdb's "allocation length" field.  If this option  is  given
	      and  LEN is greater than 0 then only one INQUIRY command is sent. Since many simple devices implement the INQUIRY command badly (and
	      do not support VPD pages) then the safest value to use for LEN is 36. See the sg_inq man page for the more information.

       -p, --page=PG
	      where PG is the VPD page to be decoded or output. The PG argument can either be an abbreviation, a number or a pair or numbers sepa-
	      rated  by  a comma. The VPD page abbreviations can be seen by using the --enumerate option. If a number is given it is assumed to be
	      decimal unless it has a hexadecimal indicator which is either a leading '0x' or a trailing 'h'. If one number is given  then  it	is
	      assumed  to be a VPD page number. If two numbers are given the second number indicates which vendor specific VPD page to decode when
	      several pages share the same VPD page number. If this option is not given (nor '-i', '-l' nor '-V') then the "Supported  VPD  pages"
	      (0x0) VPD page is fetched and decoded. If PG is '-1' or 'sinq' then the standard INQUIRY response is output.

       -q, --quiet
	      suppress the amount of decoding output.

       -r, --raw
	      output requested VPD page in binary. The output should be piped to a file or another utility when this option is used. The binary is
	      sent to stdout, and errors are sent to stderr.

       -v, --verbose
	      increases the level or verbosity.

       -V, --version
	      print out version string then exit.

ATA INFORMATION VPD PAGE

       This VPD page (0x89 or 'ai') is defined by the SCSI to ATA Translation standard. It contains information about the SAT layer,  the  "signa-
       ture" of the ATA device and the response to the ATA IDENTIFY (PACKET) DEVICE command. The latter part has 512 bytes of identity, capability
       and settings data which the hdparm utility is capable of decoding (so this utility doesn't decode it).

       To unclutter the output for this page, the signature and the IDENTIFY (PACKET) DEVICE response are not output unless the --long option  (or
       --hex  or --raw) are given. When the --long option is given the IDENTIFY (PACKET) DEVICE response is output as 256 (16 bit) words as is the
       fashion for ATA devices. To see that response as a string of bytes use the '-HH' option. To format the output suitable for hdparm to decode
       use  either  the  '-HHH'  or '-rr' option. For example if 'dev/sdb' is a SATA disk behind a SAT layer then this command: 'sg_vpd -p ai -HHH
       /dev/sdb | hdparm --Istdin' should decode the ATA IDENTIFY (PACKET) DEVICE response.

NOTES

       Since some VPD pages (e.g. the Extended INQUIRY page) depend on settings in the	standard  INQUIRY  response,  then  the  standard  INQUIRY
       response  is  output  as  a  pseudo  VPD page when PG is set to '-1' or 'sinq'. Also the decoding of some fields (e.g. the Extended INQUIRY
       page's SPT field) is expanded when the '--long' option is given using the standard INQUIRY response information (e.g. the PDT and the  PRO-
       TECT fields).

       In  the	2.4  series  of Linux kernels the DEVICE must be a SCSI generic (sg) device. In the 2.6 series block devices (e.g. disks and ATAPI
       DVDs) can also be specified. For example "sg_inq /dev/sda" will work in the 2.6 series kernels. From lk	2.6.6  other  SCSI  "char"  device
       names may be used as well (e.g. "/dev/st0m").

EXIT STATUS

       The exit status of sg_vpd is 0 when it is successful. Otherwise see the sg3_utils(8) man page.

EXAMPLES

       The  examples  in this page use Linux device names. For suitable device names in other supported Operating Systems see the sg3_utils(8) man
       page.

       To see the VPD pages that a device supports, use with no options. The command  line  invocation	is  shown  first  followed  by	a  typical
       response:

	  # sg_vpd /dev/sdb
       Supported VPD pages VPD page:
	 Supported VPD pages [sv]
	 Unit serial number [sn]
	 Device identification [di]
	 Extended inquiry data [ei]
	 Block limits (SBC) [bl]

       To  see the VPD page numbers associated with each supported page then add the '--long' option to the above command line. To view a VPD page
       either its number or abbreviation can be given to the '--page=' option. The page name abbreviations are shown within square brackets above.
       In the next example the Extended inquiry data VPD page is listed:

	  # sg_vpd --page=ei /dev/sdb
       extended INQUIRY data VPD page:
	 ACTIVATE_MICROCODE=0 SPT=0 GRD_CHK=0 APP_CHK=0 REF_CHK=0
	 UASK_SUP=0 GROUP_SUP=0 PRIOR_SUP=0 HEADSUP=1 ORDSUP=1 SIMPSUP=1
	 WU_SUP=0 CRD_SUP=0 NV_SUP=0 V_SUP=0
	 P_I_I_SUP=0 LUICLR=0 R_SUP=0 CBCS=0
	 Multi I_T nexus microcode download=0
	 Extended self-test completion minutes=0
	 POA_SUP=0 HRA_SUP=0 VSA_SUP=0

       Further examples can be found on the http://sg.danny.cz/sg/sg3_utils.html web page.

AUTHOR

       Written by Doug Gilbert

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright (C) 2006-2011 Douglas Gilbert
       This  software  is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
       POSE.

SEE ALSO

       sg_inq(sg3_utils), sg3_utils(sg3_utils), sdparm(sdparm), hdparm(hdparm)

sg3_utils-1.33							   October 2011 							 SG_VPD(8)