Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hello,
Is there any API or any other approach to detect whether the network cable is connected to the network adapter, say, en0, en1 or en2?
The OS is AIX6.1.
Thank you. (4 Replies)
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OSF1
netconfig
netconfig(8) System Manager's Manual netconfig(8)NAME
netconfig - Launches the SysMan Menu to the Network Setup Wizard
SYNOPSIS
/usr/sbin/netconfig
/usr/sbin/sysman net_wizard
DESCRIPTION
The Network Setup Wizard of the SysMan Menu can be used to configure and modify the configuration of a TCP/IP network on a Tru64 UNIX sys-
tem.
Use the Network Setup Wizard, netconfig, to do the following: Configure network interfaces, such as Ethernet, FDDI and Token Ring and
existing ATM interfaces Enable and disable the following daemons: gated, joind, routed, and rwhod Configure the system as an IP router Add,
modify, and delete entries in the following files: /etc/routes, /etc/gateways, etc/hosts, /etc/hosts.equiv, and /etc/networks
Online help is available for the Network Management dialog boxes. To get help, click on any Help button.
RESTRICTIONS
You must be root or have the appropriate privileges to run this application.
FILES
Specifies the environment variables that define the netconfig configuration on your system Specifies Internet routing information Specifies
the host name file Specifies the trusted hosts file Specifies the network name file Specifies Internet static routing information
SEE ALSO
Commands: ifconfig(8), netsetup(8), rc.config(8), rcinet(8), sysman_menu(8)
Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4)
Networking: network_manual_setup(7)netconfig(8)