05-18-2012
Network interface-
Hello,
Please what's the difference between:
Quote:
eth1 Link encap:Ethernet HWaddr 08:00:27:3a:0d:6b
inet addr:192.168.56.102 Bcast:192.168.56.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe3a:d6b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:29 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1180 (1.1 KB) TX bytes:8350 (8.3 KB)
AND
Quote:
eth0 Link encap:Ethernet HWaddr 08:00:27:0b:17:dd
inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe0b:17dd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:25 errors:0 dropped:0 overruns:0 frame:0
TX packets:54 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3330 (3.3 KB) TX bytes:10363 (10.3 KB)
Thank you so much
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
ifdata
ifdata(1) ifdata(1)
NAME
ifdata - get network interface info without parsing ifconfig output
SYNOPSIS
ifdata [options] {iface}
DESCRIPTION
ifdata can be used to check for the existence of a network interface, or to get information abut the interface, such as its IP address. Un-
like ifconfig or ip, ifdata has simple to parse output that is designed to be easily used by a shell script.
OPTIONS
-h Print out a help summary.
-e Test to see if the interface exists, exit nonzero if it does not.
-p Prints out the whole configuration of the interface.
-pe Prints "yes" or "no" if the interface exists or not.
-pa Prints the IPv4 address of the interface.
-pn Prints the netmask of the interface.
-pN Prints the network address of the interface.
-pb Prints the broadcast address of the interface.
-pm Prints the MTU of the interface.
Following options are Linux only.
-ph Prints the hardware address of the interface.
-pf Prints the flags of the interface.
-si Prints out all the input statistics of the interface.
-sip Prints the number of input packets.
-sib Prints the number of input bytes.
-sie Prints the number of input errors.
-sid Prints the number of dropped input packets.
-sif Prints the number of input fifo overruns.
-sic Print the number of compressed input packets.
-sim Prints the number of input multicast packets.
-so Prints out all the output statistics of the interface.
-sop Prints the number of output packets.
-sob Prints the number of output bytes.
-soe Prints the number of output errors.
-sod Prints the number of dropped output packets.
-sof Prints the number of output fifo overruns.
-sox Print the number of output collisions.
-soc Prints the number of output carrier losses.
-som Prints the number of output multicast packets.
-bips Prints the number of bytes of incoming traffic measured in one second.
-bops Prints the number of bytes of outgoing traffic measured in one second.
AUTHOR
Benjamin BAYART
2006-03-07 ifdata(1)