05-04-2012
Hello PSP, I think the best way once you extended the virtual lun might be to use a bootable linux CD. It is a long procedure and risky but it can be done.
Regards.
9 More Discussions You Might Find Interesting
1. SuSE
Hi All,
I have a system running with Suse Enterprise Linux 9.0.
xyz# uname -a
Linux xyz 2.4.21-291-smp #1 SMP Tue May 24 14:07:45 UTC 2005 i686 unknown
I would like to configure postfix on this system for sending mails as a root user using "mail" command to smtp server (Windows System)... (5 Replies)
Discussion started by: jumadhiya
5 Replies
2. SuSE
Hi,
I have installed LKCD using lkcdutils pakage through Yast install and remove applications. I have used enterprise server cd for installation.
But I did not found any service of lkcd like /etc/init.d/boo.lkcd there.
if we dont have this servers lkcd dump can not be saved at dump... (0 Replies)
Discussion started by: bryanabhay
0 Replies
3. Red Hat
Hi,
My linux server working with LVM partition and with /boot partition, now my /boot partition is full, now i need to extend my boot partition. can i know how to do it, without any data loss.
Regards,
M.Selva Prakash (4 Replies)
Discussion started by: mselvaprakash
4 Replies
4. HP-UX
hi,
I want to know that "What Happen if the root partition gets full on the server? I have HP-Unix 11.11 installed. (3 Replies)
Discussion started by: majidtahir
3 Replies
5. Red Hat
hi all,
As going thru LVM concepts in rhel 6, got hit with a question about "how to use the raw partition of an harddisk which extended volume is taken a bit"
please find the attached diagram...
is it possible to use this raw space with previously created extended partition without data... (13 Replies)
Discussion started by: redhatlbug
13 Replies
6. UNIX for Dummies Questions & Answers
OK, I've been thrown into an issue at my company where the security folks want password aging turned on for their limited NIS environment.
The config is a SunOS5.10 (Solaris 10) Master with several slaves and several SuSe Enterprise Server 11 Clients.
What I'm looking to understand is... (0 Replies)
Discussion started by: rzrv15
0 Replies
7. UNIX and Linux Applications
Is there any SUSE enterprise 12 x86_32 version available? I have SUSE enterprise 12 x86_64 and I am unable to compile 32 programs in that. It looks to be that gcc compiler (32 bit) does not come with SUSE 12. How can I get that?
Regards,
George (6 Replies)
Discussion started by: George47
6 Replies
8. Solaris
Hi,
I need to extend a soft partition from 20G to 100G. New disk is already added as a meta device. This soft partition is already assigned to a guest LDOM. Can someone let me know the steps to increase soft partition so guest LDOM can recognize the new space.
Thanks (1 Reply)
Discussion started by: Gho
1 Replies
9. SuSE
hello All,
good day to you.
could you tell me is there any way I can download SUSE lunux enterprise server trail version ?
I want to install sap application over it.
thanks in advance. (1 Reply)
Discussion started by: Leaner_963
1 Replies
LEARN ABOUT DEBIAN
voldump
VOLDUMP(8) AFS Command Reference VOLDUMP(8)
NAME
voldump - Dump an AFS volume without using the Volume Server
SYNOPSIS
voldump -part <partition> -volumeid <volume id>
[-file <dump file>] [-verbose] [-help]
voldump -p <partition> -vo <volume id>
[-f <dump file>] [-ve] [-h]
DESCRIPTION
voldump dumps an AFS volume in the format used by vos dump without using the Volume Server. It must be run on the file server machine and
usually must be run as the superuser "root" to have permissions to read the file server data. It's primary use is to recover data from a
file server machine where the Volume Server cannot be started for some reason.
The dump output will go to standard output, or to a file if -file is specified. vos restore can be used to load the resulting dump into a
new AFS volume. voldump always does a full dump.
CAUTIONS
Normally, use vos dump instead of this command. voldump is a tool of last resort to try to extract data from the raw data structures
stored on the file server machine and is not as regularly tested or used as the normal vos dump implementation.
If the AFS volume being dumped changes while voldump is running, the results may be inconsistent. If the File Server and Volume Server are
running, stop them with bos shutdown or a similar method before running this command.
OPTIONS
-part <partition>
Names the partition on which the volume to be dumped is located. voldump does not take the normal full range of ways of specifying a
partition. Instead, partition must be either a single letter between "a" and "z", corresponding to /vicepa through /vicepz, or the
full path to the file server partition. "aa" is not recognized; use /vicepaa instead.
-volumeid <volume id>
Specifies the ID of the volume to dump. The volume must be specified by numeric ID, not by name.
-file <dump file>
Specifies the output file for the dump. If this option is not given, the volume will be dumped to standard output.
-verbose
Asks for a verbose trace of the dump process. This trace information will be sent to standard error.
EXAMPLES
The following command dumps the volume 1936964939 on the /vicepb partition to the file /tmp/volume.dump:
% voldump -part /vicepb -volumeid 1936964939 -file /tmp/volume.dump
PRIVILEGE REQUIRED
The issuer must have read access to the file server data stored in the specified partition. Usually, this means that the issuer must be
the local superuser "root" on the file server machine.
SEE ALSO
bos_shutdown(8), restorevol(1), volserver(8), vos_dump(1), vos_restore(1)
COPYRIGHT
Copyright 2005 Russ Allbery <rra@stanford.edu>
This documentation is covered by the IBM Public License Version 1.0. This man page was written by Russ Allbery for OpenAFS.
OpenAFS 2012-03-26 VOLDUMP(8)