03-18-2012
Look in /proc
cat /proc/scsi/scsi
Exemple of output
cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: HP Model: Ultrium 5-SCSI Rev: I3BW
Type: Sequential-Access ANSI SCSI revision: 06
Host: scsi0 Channel: 00 Id: 00 Lun: 01
Vendor: HP Model: MSL G3 Series Rev: 1000
Type: Medium Changer ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: HP Model: Ultrium 5-SCSI Rev: I3BW
Type: Sequential-Access ANSI SCSI revision: 06
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: TEAC Model: DV-28S-W Rev: C.2D
Type: CD-ROM
Or, search quantum in /var/log/messages* or dmesg
Or reboot the server, and at redhat boot, you must see a line about the drive (previous to reboot, remove the option rhgb in /boot/grub/grub.conf) in order to have at boot level, only text, no graphic mode)
Last edited by SolarMax; 03-21-2012 at 11:51 AM..
8 More Discussions You Might Find Interesting
1. Solaris
Hello Expert,
I'm new from unix I just want to ask how to check what particullar tape drive installed on my SUN Ultra 450.
thanks (1 Reply)
Discussion started by: eykyn17
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
3. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
4. AIX
Dear all,
I have ultriam3 tape. It is connected my LPAR. I have that the Sl.Nos. and slot number. but run the cfmgr i am not getting the tape drive.
I have fired the command lsdev -Cc tape but no reply.
how will i configure the tape in LPAR?
Please suggest. It is very urgent. (3 Replies)
Discussion started by: pernasivam
3 Replies
5. AIX
Hello everyone
I have a problem with one of my drives in an aix box. The library is a 3583 and Aix is 5.3 TL9
The problem was that the fibre channel not work and I change the fibre but when I logging to the aix box I got this in the rmt3
lsdev | grep rmt
rmt0 Available 03-08-00-6,0... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
6. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
7. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
TS(4) Kernel Interfaces Manual TS(4)
NAME
ts - TS-11 magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NTS ts_drives # TS11
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ts ? 172520 224 5 tsintr # ts11 driver
major device number(s):
raw: 8
block: 2
minor device encoding:
bits 0003 specify TS drive
bit 0004 specifies no-rewind operation
bit 0010 ignored
DESCRIPTION
The ts-11 combination provides a standard tape drive interface as described in mtio(4). The ts-11 operates only at 1600 bpi, and only one
transport is possible per controller.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO
mt(1), tar(1), tp(1), mtio(4), ht(4), tm(4), dtab(5), autoconfig(8)
DIAGNOSTICS
ts%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
ts%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
ts%d: hard error bn%d xs0=%b xs1=%b xs2=%b xs3=%b. A hard error occurred on the tape at block bn; status registers 0-3 are printed in
octal and symbolically decoded as bits.
ts%d: addr mod 4 != 0. The address of a TS-11 command packet was not on an even longword boundary.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The device lives at the same address as a tm-11 tm(4).
3rd Berkeley Distribution January 28, 1988 TS(4)