Sponsored Content
Operating Systems Solaris Hardware RAID not recognize the new disk [Sun T6320] Post 302598649 by hicksd8 on Wednesday 15th of February 2012 04:39:02 AM
Old 02-15-2012
You need to ensure that the swapped disk has at least the same, if not more, LBA's than the disk its going to mirror. Many times I have seen what appears to be the same model of disk with different LBA's.

If the disk has even one less LBA than the one being mirrored then the controller will refuse to do it (even though the disk can be physically seen by the system).
 

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID

I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies

2. Solaris

Sun T5120 hardware RAID question

Hi everyone I've just purchased a Sun T5120 server with 2 internal disks. I've configured hardware RAID (mirror) and as a result the device tree in Solaris only contains 1 hard drive. My question is, how would I know when one of the drives become faulty? Thanks (2 Replies)
Discussion started by: soliberus
2 Replies

3. Solaris

Add new disk to Sun StorEdge 3310 RAID

HI guys. Bit of a noob so bear with me. I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Discussion started by: jamie_collins
4 Replies

4. Hardware

Sun Blade T6320 memory configuration

Can you mix DIMMs in a T6320 (sparc) blade? I have read/heard that the DIMMs in a memory bay must be identical but can you have different size DIMMs installed in the blade? For instance, can you have 1 4GB DIMM in bay 0, 2 2GB DIMMs in bay 1, 4 1 GB DIMMs in bay 2 and 2 2GB DIMMs in bay 3 for a... (0 Replies)
Discussion started by: bluescreen
0 Replies

5. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help. (2 Replies)
Discussion started by: presul
2 Replies

6. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies

7. Solaris

Solaris recognize HW Raid ??

Hardware: HP P2000 HP DL380 G7 with Solaris Software: Solaris 10 05/08 I had made a Hardware raid on P2000 and install solaris on G7, The raid card controller is working fine. How can I make the raid works on OS?? "raidclt" is getting nothing :wall::wall: Thanks (11 Replies)
Discussion started by: stanley1024
11 Replies

8. Hardware

Sun T3-1 hardware RAID

Hi all I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS. The documentation doesn't make it clear if: 1. The... (6 Replies)
Discussion started by: soliberus
6 Replies

9. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My... (4 Replies)
Discussion started by: KhawHL
4 Replies
AAC(4)							   BSD Kernel Interfaces Manual 						    AAC(4)

NAME
aac -- Adaptec AdvancedRAID Controller driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device pci device aac device aacp To compile in debugging code: options AAC_DEBUG=N Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): aac_load="YES" DESCRIPTION
The aac driver provides support for the Adaptec AAC family of SCSI Ultra2, Ultra160, and Ultra320, SATA and SAS RAID controllers. Access to RAID containers is available via the /dev/aacd? device nodes. The aacp device enables the SCSI pass-thru interface and allows devices connected to the card such as CD-ROMs to be available via the CAM scsi(4) subsystem. Note that not all cards allow this interface to be enabled. The /dev/aac? device nodes provide access to the management interface of the controller. One node exists per installed card. The aliases /dev/afa? and /dev/hpn? exist for compatibility with the Dell and HP versions of management tools, respectively. If the kernel is compiled with the COMPAT_LINUX option, or the aac_linux.ko and linux.ko modules are loaded, the Linux-compatible ioctl(2) interface for the management device will be enabled and will allow Linux-based management applications to control the card. HARDWARE
Controllers supported by the aac driver include: o Adaptec AAC-364 o Adaptec RAID 2045 o Adaptec RAID 2405 o Adaptec RAID 2445 o Adaptec RAID 2805 o Adaptec RAID 3085 o Adaptec RAID 31205 o Adaptec RAID 31605 o Adaptec RAID 5085 o Adaptec RAID 51205 o Adaptec RAID 51245 o Adaptec RAID 51605 o Adaptec RAID 51645 o Adaptec RAID 52445 o Adaptec RAID 5405 o Adaptec RAID 5445 o Adaptec RAID 5805 o Adaptec SAS RAID 3405 o Adaptec SAS RAID 3805 o Adaptec SAS RAID 4000SAS o Adaptec SAS RAID 4005SAS o Adaptec SAS RAID 4800SAS o Adaptec SAS RAID 4805SAS o Adaptec SATA RAID 2020SA ZCR o Adaptec SATA RAID 2025SA ZCR o Adaptec SATA RAID 2026ZCR o Adaptec SATA RAID 2410SA o Adaptec SATA RAID 2420SA o Adaptec SATA RAID 2610SA o Adaptec SATA RAID 2620SA o Adaptec SATA RAID 2810SA o Adaptec SATA RAID 2820SA o Adaptec SATA RAID 21610SA o Adaptec SCSI RAID 2020ZCR o Adaptec SCSI RAID 2025ZCR o Adaptec SCSI RAID 2120S o Adaptec SCSI RAID 2130S o Adaptec SCSI RAID 2130SLP o Adaptec SCSI RAID 2230SLP o Adaptec SCSI RAID 2200S o Adaptec SCSI RAID 2240S o Adaptec SCSI RAID 3230S o Adaptec SCSI RAID 3240S o Adaptec SCSI RAID 5400S o Dell CERC SATA RAID 2 o Dell PERC 2/Si o Dell PERC 2/QC o Dell PERC 3/Si o Dell PERC 3/Di o Dell PERC 320/DC o HP ML110 G2 (Adaptec SATA RAID 2610SA) o HP NetRAID 4M o IBM ServeRAID 8i o IBM ServeRAID 8k o IBM ServeRAID 8s o ICP RAID ICP5045BL o ICP RAID ICP5085BL o ICP RAID ICP5085SL o ICP RAID ICP5125BR o ICP RAID ICP5125SL o ICP RAID ICP5165BR o ICP RAID ICP5165SL o ICP RAID ICP5445SL o ICP RAID ICP5805BL o ICP RAID ICP5805SL o ICP ICP5085BR SAS RAID o ICP ICP9085LI SAS RAID o ICP ICP9047MA SATA RAID o ICP ICP9067MA SATA RAID o ICP ICP9087MA SATA RAID o ICP ICP9014RO SCSI RAID o ICP ICP9024RO SCSI RAID o Legend S220 o Legend S230 o Sun STK RAID REM o Sun STK RAID EM o SG-XPCIESAS-R-IN o SG-XPCIESAS-R-EX o AOC-USAS-S4i o AOC-USAS-S8i o AOC-USAS-S4iR o AOC-USAS-S8iR o AOC-USAS-S8i-LP o AOC-USAS-S8iR-LP FILES
/dev/aac? aac management interface /dev/aacd? disk/container interface DIAGNOSTICS
Compiling with AAC_DEBUG set to a number between 0 and 3 will enable increasingly verbose debug messages. The adapter can send status and alert messages asynchronously to the driver. These messages are printed on the system console, and are also queued for retrieval by a management application. SEE ALSO
kld(4), linux(4), scsi(4), kldload(8) HISTORY
The aac driver first appeared in FreeBSD 4.3. AUTHORS
Mike Smith <msmith@FreeBSD.org> Scott Long <scottl@FreeBSD.org> BUGS
This driver is not compatible with Dell controllers that have version 1.x firmware. The firmware version is the same as the kernel version printed in the BIOS POST and driver attach messages. The controller is not actually paused on suspend/resume. BSD
July 10, 2009 BSD
All times are GMT -4. The time now is 05:52 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy