12-02-2011
What architecture or OS are you talking about?
What do you mean by "connect to network"? Are you talking of your PC?
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
9. AIX
Hi,
I would like to know after the installation of vio server. how many logical network interfaces will be created on vio server if I am having two physical interfaces on vio server.
I am asking this question because I would like know to on the basis of logical network interfaces creation on... (0 Replies)
Discussion started by: manoj.solaris
0 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
talkd(8c) talkd(8c)
Name
talkd - inter-terminal communications server
Syntax
/etc/talkd
Description
The program is the server for the program. The server provides a rendezvous method for the requesting (possibly remote) and the local
responding
The server is invoked by when it receives a packet on the port indicated in the talk service specification.
Restrictions
The server does not strictly follow network byte order in its packet format and may have difficulty in talking with implementations of on
other architectures that do not take this into account.
The version of released with ULTRIX V3.0 uses a protocol that is incompatible with the protocol used in earlier versions. Starting with
ULTRIX V3.0, the program communicates with other machines running ULTRIX, V3.0 (and later), and machines running 4.3 BSD or versions of
UNIX based on 4.3 BSD.
The command is not 8-bit clean. Typing in DEC Multinational Characters (DECMCS) causes the characters to echo as a sequence of a carets (^)
followed by the character represented with its high bit cleared. This limitation makes unusable if you want to communicate using a language
which has DECMCS characters in its alphabet.
See Also
talk(1), services(5), inetd(8c), ntalkd(8c)
talkd(8c)