I have worked with Qlogic (Sun) fiber cards a lot and with Emulex fiber cards only a little. Here is the scenario: I have a Sun 490 with 3 Emulex cards in it. A pair are for the 6120 array that is attached, the other is a direct attach so our SAN for Veritas Netbackup to back up the system.I... (0 Replies)
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
LEARN ABOUT HPUX
prtdiag
prtdiag(1M)prtdiag(1M)NAME
prtdiag - display system diagnostic information
SYNOPSIS
/usr/sbin/prtdiag [-v] [-l]
prtdiag displays system configuration and diagnostic information on sun4u and sun4v systems.
The diagnostic information lists any failed field replaceable units (FRUs) in the system.
The interface, output, and location in the directory hierarchy for prtdiag are uncommitted and subject to change in future releases.
prtdiag does not display diagnostic information and environmental status when executed on the Sun Enterprise 10000 server. See the
/var/opt/SUNWssp/adm/${SUNW_HOSTNAME}/messages file on the system service processor (SSP) to obtain such information for this server.
The following options are supported:
-l Log output. If failures or errors exist in the system, output this information to syslogd(1M) only.
-v Verbose mode. Displays the time of the most recent AC Power failure, and the most recent hardware fatal error information, and (if
applicable) environmental status. The hardware fatal error information is useful to repair and manufacturing for detailed diagnos-
tics of FRUs.
The following exit values are returned:
0 No failures or errors are detected in the system.
1 Failures or errors are detected in the system.
2 An internal prtdiag error occurred, for example, out of memory.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWkvm |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable* |
+-----------------------------+-----------------------------+
*The output is unstable.
modinfo(1M), prtconf(1M), psrinfo(1M), sysdef(1M), syslogd(1M), attributes(5), openprom(7D)NOTES
Not all diagnostic and system information is available on every Solaris platforn, and therefore cannot be displayed by prtdiag. On those
platforms, further information can be obtained from the System Controller.
29 Aug 2005 prtdiag(1M)