Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
LEARN ABOUT MOJAVE
locale::codes::langfam
Locale::Codes::LangFam(3pm) Perl Programmers Reference Guide Locale::Codes::LangFam(3pm)NAME
Locale::Codes::LangFam - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangFam;
$lext = code2langfam('apa'); # $lext gets 'Apache languages'
$code = langfam2code('Apache languages'); # $code gets 'apa'
@codes = all_langfam_codes();
@names = all_langfam_names();
DESCRIPTION
The "Locale::Codes::LangFam" module provides access to standard codes used for identifying language families, such as those as defined in
ISO 639-5.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 639-5
language family codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language families. A code set may be specified using either a name, or a
constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langfam('apa','alpha');
$lext = code2langfam('apa',LOCALE_LANGFAM_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from ISO 639-5 such as 'apa' for Apache languages.
This is the default code set.
ROUTINES
code2langfam ( CODE [,CODESET] )
langfam2code ( NAME [,CODESET] )
langfam_code2code ( CODE ,CODESET ,CODESET2 )
all_langfam_codes ( [CODESET] )
all_langfam_names ( [CODESET] )
Locale::Codes::LangFam::rename_langfam ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangFam::add_langfam ( CODE ,NAME [,CODESET] )
Locale::Codes::LangFam::delete_langfam ( CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_alias ( NAME ,NEW_NAME )
Locale::Codes::LangFam::delete_langfam_alias ( NAME )
Locale::Codes::LangFam::rename_langfam_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::delete_langfam_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.loc.gov/standards/iso639-5/id.php
ISO 639-5 .
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangFam(3pm)