02-25-2011
You are most welcome, but was it helpful?
take care
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
3. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
4. Solaris
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Discussion started by: Y4Net
23 Replies
5. Solaris
Hi Gurus
I need to know few things related to HBA port & fcinfo command
I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Discussion started by: girish.batra
6 Replies
6. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
7. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
8. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Solaris
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT MOJAVE
slapo-syncprov
SLAPO-SYNCPROV(5) File Formats Manual SLAPO-SYNCPROV(5)
NAME
slapo-syncprov - Sync Provider overlay to slapd
SYNOPSIS
/etc/openldap/slapd.conf
DESCRIPTION
The Sync Provider overlay implements the provider-side support for the LDAP Content Synchronization (RFC4533) as well as syncrepl replica-
tion support. The overlay can be used with any backend that maintains entryCSN and entryUUID attributes for its entries. It also creates a
contextCSN attribute in the root entry of the database.
The contextCSN is updated for every write operation performed against the database. To reduce database contention, the contextCSN is only
updated in memory. The value is written to the database on server shutdown and read into memory on startup, and maintained in memory there-
after. Checkpoints may be configured to write the contextCSN into the underlying database to minimize recovery time after an unclean shut-
down.
On databases that support inequality indexing, it is helpful to set an eq index on the entryCSN attribute when using this overlay.
CONFIGURATION
These slapd.conf options apply to the Sync Provider overlay. They should appear after the overlay directive.
syncprov-checkpoint <ops> <minutes>
After a write operation has succeeded, write the contextCSN to the underlying database if <ops> write operations or more than <min-
utes> time have passed since the last checkpoint. Checkpointing is disabled by default.
syncprov-sessionlog <ops>
Configures an in-memory session log for recording information about write operations made on the database. The <ops> specifies the
number of operations that are recorded in the log. All write operations (except Adds) are recorded in the log. When using the ses-
sion log, it is helpful to set an eq index on the entryUUID attribute in the underlying database.
syncprov-nopresent TRUE | FALSE
Specify that the Present phase of refreshing should be skipped. This value should only be set TRUE for a syncprov instance on top of
a log database (such as one managed by the accesslog overlay). The default is FALSE.
syncprov-reloadhint TRUE | FALSE
Specify that the overlay should honor the reloadHint flag in the Sync Control. In OpenLDAP releases 2.3.11 and earlier the syncrepl
consumer did not properly set this flag, so the overlay must ignore it. This option should be set TRUE when working with newer
releases that properly support this flag. It must be set TRUE when using the accesslog overlay for delta-based syncrepl replication
support. The default is FALSE.
FILES
/etc/openldap/slapd.conf
default slapd configuration file
SEE ALSO
slapd.conf(5), slapd-config(5), slapo-accesslog(5). OpenLDAP Administrator's Guide.
ACKNOWLEDGEMENTS
OpenLDAP Software is developed and maintained by The OpenLDAP Project <http://www.openldap.org/>. OpenLDAP Software is derived from Uni-
versity of Michigan LDAP 3.3 Release.
OpenLDAP 2.4.28 2011/11/24 SLAPO-SYNCPROV(5)