11-11-2010
problem of networking in centos
Hello,
I am using dual boot of linux, one is ubuntu and the other is one is centos.
I have three NIC's and only one of them connected with cable.
The thing is that when I boot from the ubuntu, it does recognize it and I am connected to the Internet.
When I boot from the centos I am not connected to the Internet and when I do ifconfig then it tell me that my IP is 127.0.0.1 (loop back).
From ubuntu I know that it is eth1 that is connected with the cable.
Now how do I configure centos to recognize it and to connect to the network?
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
How to check whether a port is working properly or not ?
I am getting a Error message Could not open connection to the host, on port 23: Connect failed.
Thanks !! (1 Reply)
Discussion started by: dreams5617
1 Replies
2. Solaris
Unable to Ping network nodes
Currently have two Solaris 10 servers connected via a dumb Hub. I'm unable to ping either box but they can ping themselves. I have double checked physical connections and the following files;
/etc/hosts - verified that all devices are listed correctly... (4 Replies)
Discussion started by: pham
4 Replies
3. UNIX for Advanced & Expert Users
Hi all,
When I tried to restart the networking daemon, it stated this error:
MyServer:/etc/init.d# ./networking restart
Reconfiguring network interfaces...RTNETLINK answers: Network is unreachable
run-parts: /etc/network/if-up.d/route exited with return code 2
done.
Please note that I... (2 Replies)
Discussion started by: mjdousti
2 Replies
4. Solaris
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.13.157.127 netmask ffffffc0 broadcast 10.135.151.191
ether 0:14:4f:a0:e3:3a
e1000g1: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 8
inet 10.13.157.227 netmask ffffffc0... (3 Replies)
Discussion started by: sunnybee
3 Replies
5. IP Networking
Hi, I am running scientific linux guest on ubuntu host.
The problem is that the guest machine doesn't have any ip except from the loopback.
I want that the guest OS will be in the same local network of the host and not part of internal network that virtualbox create.
In other words I... (1 Reply)
Discussion started by: programAngel
1 Replies
6. IP Networking
Guide on how to disable ipv6 for Centos and RedHat
1) Edit /etc/sysconfig/network-scripts/ifcfg-eth0 and change:
NETWORKING_IPV6=yes to NETWORKING_IPV6=no
2) Edit /etc/modprobe.conf and add these lines:
alias net-pf-10 off
alias ipv6 off
3) Stop the ipv6tables service:
... (0 Replies)
Discussion started by: zanna91
0 Replies
7. Red Hat
Hey guys, I've reached the point of setting up VM's on XEN but the net installations seem to be failing when I am in the netinstall on the actual VM, so this leads me to believe that the networking on the host machine is not set up correctly. I am running CentOS 5.9 along with XEN and was just... (0 Replies)
Discussion started by: mccabec123
0 Replies
8. Red Hat
Hi ,
I have install centos6.3 64bit, other things are working fine.:b:
I am trying to use bluetooth. It is showing bluetooth icons and options only turn on and turn off bletooth.:confused:
How to enable full features of bluetooth like search, send file etc.:wall: (7 Replies)
Discussion started by: Priy
7 Replies
9. Red Hat
hi
I installed Openvas we have the following problem
internet Connection is Ok
Even Reinstall the problem is not resolved
Openvas Setup, Version: 0.5
Step 1: Update NVT's and SCAP data
Please note this step could take some time.
Once completed, NVT's and SCAP data will be updated... (12 Replies)
Discussion started by: mnnn
12 Replies
10. UNIX for Beginners Questions & Answers
Hallo to everyone.From sometime i have problems with my asterisk pbx on cent os which is in corosync cluster mode with resource groups.The problem is for time the cluster just swap the active one with the other and the only messages in \var\log\messages is that bond0:link status defenitly down for... (0 Replies)
Discussion started by: evolintend
0 Replies
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)
NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces.
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5,) rc.conf(5), ifconfig(8)
HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD
July 26, 2009 BSD