10-12-2010
Quote:
The
sleep utility shall suspend execution for at least the integral number of
seconds specified by the time operand.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am running a number of processes through a kill -15 loop as a temporary fix to some viscious memory leaks. I cannot pass the entire list of processes through the kill at once, because the nature of the monitoring my client has will cause the software to failover.
Because of the large number of... (1 Reply)
Discussion started by: mattd
1 Replies
2. UNIX for Dummies Questions & Answers
If I give sleep(50) what does it mean?
My program waits for further execution or all my other processes wait? (3 Replies)
Discussion started by: leewar
3 Replies
3. Shell Programming and Scripting
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Discussion started by: Glove
1 Replies
4. UNIX for Dummies Questions & Answers
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Discussion started by: dr46014
3 Replies
5. UNIX for Dummies Questions & Answers
sleep 10 &
Is this the write line of command to suspend 5 jobs for 10 minutes (6 Replies)
Discussion started by: senyor17
6 Replies
6. UNIX for Dummies Questions & Answers
Hi Forum
Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this
here my code
sleepVal=5
while
do
... (3 Replies)
Discussion started by: ShinTec
3 Replies
7. Shell Programming and Scripting
Hi All,
i am very new to shall script . i am not that much aware of sleep command ,
i want to terminate the sleep command after certain time.
following is my code.
while
loop
sleep 1800
messag=/status.sql
donethe script will be on sleep untill the messag be comes P. here my requirement... (4 Replies)
Discussion started by: mandlysreedhar
4 Replies
8. Shell Programming and Scripting
Hello,
Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email.
#!/bin/ksh
mailto=`cat... (2 Replies)
Discussion started by: bbbngowc
2 Replies
9. Shell Programming and Scripting
Hi Frnz,
I need to execute sleep command but i dont know the definite time.
Let me put my req:
I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
Discussion started by: gnnsprapa
6 Replies
10. Shell Programming and Scripting
I need help in script.
I want my one script execute every time at 6:30 am and i have no cron access.
So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue,
So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
SLEEP(1) BSD General Commands Manual SLEEP(1)
NAME
sleep -- suspend execution for an interval of time
SYNOPSIS
sleep seconds
DESCRIPTION
The sleep command suspends execution for a minimum of seconds.
If the sleep command receives a signal, it takes the standard action.
IMPLEMENTATION NOTES
The SIGALRM signal is not handled specially by this implementation.
The sleep command will accept and honor a non-integer number of specified seconds (with a '.' character as a decimal point). This is a non-
portable extension, and its use will nearly guarantee that a shell script will not execute properly on another system.
EXIT STATUS
The sleep utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
To schedule the execution of a command for x number seconds later (with csh(1)):
(sleep 1800; sh command_file >& errors)&
This incantation would wait a half hour before running the script command_file. (See the at(1) utility.)
To reiteratively run a command (with the csh(1)):
while (1)
if (! -r zzz.rawdata) then
sleep 300
else
foreach i (`ls *.rawdata`)
sleep 70
awk -f collapse_data $i >> results
end
break
endif
end
The scenario for a script such as this might be: a program currently running is taking longer than expected to process a series of files, and
it would be nice to have another program start processing the files created by the first program as soon as it is finished (when zzz.rawdata
is created). The script checks every five minutes for the file zzz.rawdata, when the file is found, then another portion processing is done
courteously by sleeping for 70 seconds in between each awk job.
SEE ALSO
nanosleep(2), sleep(3)
STANDARDS
The sleep command is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
HISTORY
A sleep command appeared in Version 4 AT&T UNIX.
BSD
April 18, 1994 BSD