09-24-2010
Greentings all,
Apologies for my delayed response:
May thanks for the replies; much appreciated. I uninstalled the original jumpstart
config I used and installed JET I still get replies from rpcinfo, so I'm kinda happy
that the bootp server is ok...
Apologies for the delayed response:
Kumarmani: Yip it's on the same subnet ( At least I think so!! I can't get to the NIC to set an IP/MASK... but the intention is to have it on the same subnet)
DukeNuke2:
Now that's what I'm not sure of. There are physical devices in the box, although I'm not getting a status when I hook up a cable. I know the cable works because I tested it on domain 0. The other thing is that I'm not sure what MAC to assign it. I did a "banner" from the OBP and used that MAC address. Not sure how to pic up the MAC's from the other NICs as there's nothing running there and I'm not sure hw to pic it up from XSCF>
devalias returns nothing...
Unclefab:
after doing a reset-all, when I got control back, probe-scsi-all yielded nothing
I did a reset-all again and then did a watch-net-all.. also nothing:
{0} ok watch-net-all
{0} ok
Thanks for your suggestions!!
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do you install linux over the net? (1 Reply)
Discussion started by: macdonto
1 Replies
2. Solaris
I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed".
Why does this happen?
I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
Discussion started by: lydiaEd
1 Replies
3. Solaris
Hi my friends
when I want to make boot net for my server I have receive:
Time out ARP/RARP
note: I have use
Ok boot net (this is my Syntax)
so what is the problem? (2 Replies)
Discussion started by: bintaleb
2 Replies
4. Solaris
I have a blade 6000 chassis with a T6340 blade. The blade took a dump and I am trying to rebuild it with a Flash Archive. I am using net boot from an E2900 and the flash is located on a an array that is attached to my v245 management server. I can net boot and I can select flash install. When I put... (1 Reply)
Discussion started by: ryan_ford
1 Replies
5. AIX
dears
i am trying to upgrade the TL from TL7 to TL8 and i facing this issue AIX6.1
<< End of Success Section >>
+-----------------------------------------------------------------------------+
BUILDDATE Verification ...... (2 Replies)
Discussion started by: thecobra151
2 Replies
6. Solaris
Dear all,
I have a solaris 10 in my environment (VMware virtual machine). recently I increased the harddisk size from the VMware and reboot my server. after reboot the os is unable to boot and gives the below error message.
exec(/sbin/init) file not found
press any key to restart
... (3 Replies)
Discussion started by: krishna001
3 Replies
7. Solaris
I have M10-1. Installation OS 10 from cdrom external.
Here message from OK Prompt
{0} ok probe-scsi-all
/pci@8000/pci@4/pci@0/pci@2/pci@0/usb@4,1/cdrom@1
Unit 0 Removable Read Only device HL-DT-STDVDRAM GP65NB60 PF00
But..
{0} ok boot... (3 Replies)
Discussion started by: mbahjiman
3 Replies
8. Solaris
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
Discussion started by: goya
3 Replies