09-01-2010
I highly doubt that sda2 was your D: drive, as Windows can't use an extended partition with NTFS, and most versions won't even work with more than 1 primary partition. More likely sda5 was the drive you're looking for.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I am trying to mount a FAT16 and FAT32 partition on an already installed Redhat system.
I have tried to edit the fstab and mtab, and to put in the data I got from fdisk, but it just says cannot find it.
The information given by fdisk on /dev/hda is:
Device Boot Start ... (4 Replies)
Discussion started by: ghoti
4 Replies
2. Solaris
Hello,
I have a problem on my sun station, that run solaris7.
To free temporarly a little space on /, I moved a few empty folders (mnt, net, awk, tftpboot) to the /home partition.
Unfortunately the system froze just after this...maybe I should not have move this files, I don't know, I am a... (3 Replies)
Discussion started by: nabulus
3 Replies
3. Solaris
dear all,
that is my problem :
c0d0p1 is nt,
c0d0p2 is solaris
and other on extended partition is pcfs,
so how can i mount it somewhere?
because i dont know which one connect from raw to block dev.
/dev/rdsk/c0d0p?
any help would be great... :) (6 Replies)
Discussion started by: stdout
6 Replies
4. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
5. Solaris
Dear Brothers
First i installed suse linux with the following partition. my hd0 size is 75gb
hdc1 swap 1 gb
hdc2 native linux 39gb
For the rest of the 35 gb i did not create any partition. so i planned to install solaris 10x86 on that free space.
When i installed the solaris i... (1 Reply)
Discussion started by: sayed_021
1 Replies
6. Solaris
hi,
i have created an extended partition during solaris 11 installation. My question is how this extended partition is mounted , so that i can use this partition for my work.
Thanks (2 Replies)
Discussion started by: zeeshan047
2 Replies
7. Red Hat
hi all,
As going thru LVM concepts in rhel 6, got hit with a question about "how to use the raw partition of an harddisk which extended volume is taken a bit"
please find the attached diagram...
is it possible to use this raw space with previously created extended partition without data... (13 Replies)
Discussion started by: redhatlbug
13 Replies
8. UNIX for Dummies Questions & Answers
I want to gain read/write access to a Windows 8 partition from a linux live cd. Prior to Windows 8, I used ntfs-3g to mount the partition from the command line.
The "Fdisk -l" command does not seem to be able to read efi partitions. There must be some new strategy for linux users. This is... (6 Replies)
Discussion started by: jamarsh
6 Replies
9. Red Hat
Can you please help me to remove this error.
Disk /dev/sda: 64.4 GB, 64424509440 bytes
255 heads, 63 sectors/track, 7832 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk... (4 Replies)
Discussion started by: karthik9358
4 Replies
10. AIX
Hello, today i get some aix errors (can't lock files and strange things) then i umount FS to do a fsck but i get these errors
root@omega / > fsck -p /dev/fslv06
The current volume is: /dev/fslv06
Unable to read primary superblock.
Unable to read either superblock.
I readed on this page... (9 Replies)
Discussion started by: thorin666
9 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)