07-25-2010
Thought I'd just add in here at this point I'm a bit of a dummy when it comes to UNIX..!
How to I reopen for kernel and take settings for eth card module?
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. SCO
hi,
anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies
5. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
6. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
7. SCO
I am haveing a problem with my VMware ESXi 4.1 server and a virtual SCO UnixWare 7.1.4 server that I need for a legacy application for my company. The problem seems simple but I can't find a solution. The UnixWare (UW) server is a clean install and patched as SCO recommends. I am able to telnet to... (1 Reply)
Discussion started by: DudeCrush
1 Replies
8. SCO
Hello Dears,
I have fujitsu tx300 S7 server with installed sco unixware 7.1.4,
Now the /etc is corrupted and the sco cannot boot.
There is no emergency disk or cd, I'm trying to fix this with reinstalling unixware again, but the problem now that when i try to install the HBA driver that i... (26 Replies)
Discussion started by: amr ibrahim
26 Replies
9. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT DEBIAN
doveadm-log
DOVEADM-LOG(1) Dovecot DOVEADM-LOG(1)
NAME
doveadm-log - Locate, test or reopen Dovecot's log files
SYNOPSIS
doveadm [-Dv] log errors
doveadm [-Dv] log find [directory]
doveadm [-Dv] log reopen
doveadm [-Dv] log test
DESCRIPTION
The doveadm log commands are used to locate and reopen the log files of dovecot(1). It's also possible to test the configured targets of
the *log_path settings.
OPTIONS
Global doveadm(1) options:
-D Enables verbosity and debug messages.
-v Enables verbosity, including progress counter.
COMMANDS
log errors
doveadm log errors
The log errors command is used to show the last - up to 1,000 - errors and warnings. If no output is generated, no errors have occurred
since the last start.
log find
doveadm log find [directory]
The log find command is used to show the location of the log files, to which dovecot(1) sends its log messages. If dovecot(1) logs its
messages through syslogd(8) and doveadm(1) could not find any log files, you can specify the directory where your syslogd writes its log
files.
log reopen
doveadm log reopen
This command causes doveadm to reopen all log files, configured in the log_path, info_log_path and debug_log_path settings. These settings
are configured in /etc/dovecot/conf.d/10-logging.conf.
This is for example useful after manually rotating the log files.
log test
doveadm log test
This command causes doveadm to write the message "This is Dovecot's priority log (timestamp)" to the configured log files. The used prior-
ities are: debug, info, warning, error and fatal.
EXAMPLE
This example shows how to locate the log files used by dovecot(1).
doveadm log find
Looking for log files from /var/log
Debug: /var/log/dovecot.debug
Info: /var/log/mail.log
Warning: /var/log/mail.log
Error: /var/log/mail.log
Fatal: /var/log/mail.log
REPORTING BUGS
Report bugs, including doveconf -n output, to the Dovecot Mailing List <dovecot@dovecot.org>. Information about reporting bugs is avail-
able at: http://dovecot.org/bugreport.html
SEE ALSO
doveadm(1)
Dovecot v2.1 2012-02-22 DOVEADM-LOG(1)