Visit Our UNIX and Linux User Community

Full Discussion: copy failing disk to Spare
Top Forums UNIX for Dummies Questions & Answers copy failing disk to Spare Post 302371768 by rees_a on Monday 16th of November 2009 06:59:59 AM
Old 11-16-2009
copy failing disk to Spare

Hi Guys,

I have a failing 4gb (c0t5d0) drive that contains lvol4 -8 on hp-ux. It's not the boot disk but is part of VG00 volume group. Within that group, I have a disk (c0t4d0) of the same size that has 1 lvol on it for swap(4gb) I also have a seperate 1.5 gb swap volume on another physical disk

Can I remove the 4gb swap volume(lvol9) and then somehow copy the failing disk to the now empty swap disk. If this is possible, can you please help me with the order/commands I will need to perform this.

I'm assuming the following will work just need clarification -

goto Sam and remove the 4gb Swap volume from physical disk c0t4d0

copy from c0t5d0 to c0t4d0 using 'dd if=c0t5d0 of=c0t4d0

shut server down and phyisically swap c0t5d0 for a new drive,

change c0t4d0 to c0t5d0 physical address

then reboot

does this make sense?

I'm assuming the new empty physical disk will need to be c0t4d0. Will the system recognise that lvol4-8 are on the right disk?

Any help with this will be great as I don't want to lose any data
 
Test Your Knowledge in Computers #838
Difficulty: Medium
Both SMTP and HTTP are valid application layer protocols used as transport for SOAP.
True or False?

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Help me with disk copy

I do not have a Unix machine, i do have a Linux machine.. i have a Unix boot disk that is essencial to my unit. Is there any way in Windows98 or Linux to make copies of this disk. So far i can't get either to read the disk. (1 Reply)
Discussion started by: deathsfriend
1 Replies

2. UNIX for Dummies Questions & Answers

Vfstab on spare disk - HOW ? Mount ?

Hi, guys ! Could someone clarify one thing for me: I start machine from disk0, and want to check the /etc/vfstab on disk1. How do i do it ? Tried to write: cd / mount /dev/dsk/c0t1d0s0 /mnt But if I do cd /mnt, it is empty. I expected to see disk1 there ? Or am I wrong ? How do I... (3 Replies)
Discussion started by: DGoubine
3 Replies

3. Filesystems, Disks and Memory

SCSI disk spare sectors

Is there a way to determine the number of available spare sectors on a disk ? as it may be useful for notifying a user to take a backup of the disk before it runs into a medium error. (6 Replies)
Discussion started by: rednex
6 Replies

4. Solaris

Solaris 10: how to copy whole disk?

Hi, i have problems with my system disk (os solaris 5.10) and i'm wondering if there is any way to copy the whole disk to a new one, without reinstalling everything (so to do a mirroring)?? thanks in advance (3 Replies)
Discussion started by: sprehodec
3 Replies

5. UNIX for Advanced & Expert Users

Failing to write retrieve script for tape to disk conversion

I have the below script which has been written to retrieve files from tape drive i.e. TSM server. Now i have to write the script using UNIX commands for retrieve operation but I am not able to proceed. The script is: #!/usr/local/bin/expect -f set timeout 1800 set file spawn $env(SHELL)... (0 Replies)
Discussion started by: hrsaurav
0 Replies

6. UNIX for Dummies Questions & Answers

What is in-core copy and disk-copy of i-node table?

I have found a question from the exercises of my study mat. The question is "Why are there a in-core copy and a disk-copy of i-node block and super block?" If any one know the proper answer then please send me..... (1 Reply)
Discussion started by: dearanik
1 Replies

7. UNIX for Dummies Questions & Answers

Help!! Failing HP-UX 11 system disk

Firstly, system setup - HP900 K460, 3 internal hard drives that make up the system volume group(vg00) no software mirroring HP-ux version 11.00 2 Nike 20 raid arrays attached, fully populated with 40 4gb hot swap drives(All used in production environment) I have 3 disks that make up my... (0 Replies)
Discussion started by: rees_a
0 Replies

8. AIX

IBM SAN STORAGE HOT SPARE DISK

Hello, I have DS4000 IBM SAN Storage ( aka FastT Storage ) One of my disks has failed and I had a hot spare disk covering all the arrays. As the disk failed, immediately the hotspare disk took over the failed disk ( see the JPEG in the attachment ) My Question: How can I make the hotspare... (1 Reply)
Discussion started by: filosophizer
1 Replies

9. Solaris

Use 'dd' to copy boot disk to larger target disk

Hi, I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies

10. AIX

Failing to add new NetApp disk AIX 7.1 - but no error

Hello, AIX 7.1 - several NetApp disks already running. Trying to install a new one. Storage folks provision it. I run cfgmgr - nothing. no new disks show up in "lsdev", "sanlun lun show" shows no new device. No errors, just nothing. Storage guys disconnect it and attaches to another aix server -... (5 Replies)
Discussion started by: sid
5 Replies
bootconf(4)						     Kernel Interfaces Manual						       bootconf(4)

NAME
bootconf - boot device configuration table DESCRIPTION
The file contains the address and disk layout type of the system's boot devices or lif volumes. It is used by the and HP-UX kernel control scripts (fileset to determine how and where to update the initial boot loader. Normally the kernel's script queries the system's hardware and creates the file. In rare cases when either the system configuration cannot be automatically determined or additional and/or alternate boot devices should be automatically updated, the administrator must edit the file manually. There is one line in the file for each boot device. Each line contains the following blank-separated fields in the order shown: disk type A flag indicating how the file system(s) on the disk are laid out. The flag must be one of the following: Indicates that the root disk is in LVM or VERITAS Volume Manager (VxVM) format. If LVM or VxVM mirrors are used, then each of the "mirrors" must have its own line in the file. Indicates that the root disk is in the "whole disk" format with no partitions, but boot and swap space are reserved outside the file system. device file The absolute path of the device special file that accesses the physical device where the boot area is located. For LVM root disks, the device special file is the physical volume(s) returned by the command. For "whole disks" this is the device file that references the entire disk. Blank lines are permitted. Any line beginning with a is considered to be a comment. DIAGNOSTICS
The Software Distributor log file contains diagnostic messages under the fileset if the file is incorrect. Most of the messages are self- explanatory; a few warrant additional explanation: If there are no other messages about the file is probably empty. Otherwise, the file is not in the proper format, and the other messages will explain what the problem is. The specified device file does not point to a disk where there is a lif which contains the file Some character other than or is in the first field of a line. As of release 10.0, the boot areas in must all be on the same type of disk layout. There are characters after the device file specification. EXAMPLES
The boot area is on an LVM root disk: l /dev/disk/disk7_p2 The boot area is on a whole disk layout: w /dev/disk/disk7 WARNINGS
All of the boot devices in the file must have the same disk layout. AUTHOR
was developed by the Hewlett-Packard Company. FILES
SEE ALSO
mediainit(1), hpux(1M), hpux.efi(1M), mkboot(1M), vgdisplay(1M), lif(4), intro(7). documentation. bootconf(4)

Featured Tech Videos

All times are GMT -4. The time now is 02:42 PM.
Unix & Linux Forums Content Copyright 1993-2020. All Rights Reserved.
Privacy Policy