/home/jcontreras/Desktop/echo: line 1: file2.conf: No such file or directory
This means that there's something wrong with your script, not the crontab entry. Have you tried running the script itself, instead of each command by it's own? You can get a trace of what is done by putting the line
near the beginning of your script.
Besides that, 'echo' is not really the best name for a script, as it's both an executable and a built-in command in most shells. Try to avoid such reserved names, as it can create confusion.
Hi
I have a shell script which works fine at the command line
and does works in crontab also but does not send the output to
mail as other scripts do by default.
10 1 * * * /export/home/test/report_script
by default should send the output to mail but the script
runs OK and the output... (1 Reply)
dear all ,
does any one now how can i become sure that the crontab that i put was working successfully not by looking for thr result of the sheduled task but from a log for the crontab or something similar
and i need to check that the cron i wrote is correct
00 15 * * 0,1,2,3,6... (2 Replies)
i have a ksh script that creates messages in a temp directory and then sends them out using the sendmail command and i'm trying to set it up to run every night with crontab.
So the basic gist of the script is
#create temp dir and messages
...
#loop through each message and send using sendmail... (3 Replies)
Hi All,
I've a shell script which calls a Sybase stored procedure to do some functionality. I want to schedule the running of this script by crontab. I'm using Solaris 5.8. When i executed the following command
crontab -l
i got the output as
crontab: can't open your crontab file
How... (10 Replies)
hi,
I run a .sh file using crontab. I need to know the path of the file . Previously when I run the file alone , i used "pwd" but now when using crontab it gives the temp directory of the file.
Is there any way I can find the absolute path of the file when i execute it ?
Regards,
Ranga (7 Replies)
Dear All
jobs are scheduled in crontab . To view this I use crontab -l . But suddenly today I am not able to see any jobs that is being scheduled in crontab. when I type crontab -l , I am seeing nothing.I am not logging through admin user(i dont have it).But I can schedule jobs through... (3 Replies)
Hi, can someone explain the differences between using the at and crontab commands. When would you use one command over the other?
TIA
Dom (1 Reply)
Discussion started by: domburf69
1 Replies
LEARN ABOUT OSF1
script
script(1) General Commands Manual script(1)NAME
script - Makes a transcript of terminal session
SYNOPSIS
script [-a] [file]
The script command makes a transcript of everything printed on your terminal.
OPTIONS
Appends the transcript to file rather than writing it to file.
OPERANDS
The name of an output file that will contain the transcript of the session. If this parameter is omitted, the file typescript is written.
DESCRIPTION
The transcript is written to file, or appended to file if the -a option is given. If no file name is given, the transcript is saved in the
file typescript.
The script ends when the forked shell exits.
This program is useful when you are using a CRT and want a hard-copy record of the dialog (for example, a technical writer might create an
example of a working session this way).
If you specify the -a option and the file does not exist, it is created.
If you do not specify the -a option and the file exists, it is replaced.
RESTRICTIONS
The script command requires a streams based terminal. In single user mode, streams may not be enabled. Under these circumstances, script
will exit with no action. If you are the superuser and need to run this command in single user mode, use the following special instruc-
tions.
Enabling Streams
If it is necessary to enable a streams environment in the single user mode, enter the command /sbin/init.d/streams. This command is avail-
able to the superuser only.
SEE ALSO
Commands: autopush(8), cat(1), echo(1), strsetup(8), tee(1)
System Administration
script(1)